Dtc C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction

Brake. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
Brake Control. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK DTC

READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)

CHECK STOP LIGHT SWITCH INSTALLATION

RECONFIRM DTC

INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL)

INSPECT STOP LIGHT SWITCH

DTC C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the brake actuator assembly.

Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Brake Control.Anti-Lock Brake System. Dtc C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction


DTC Code
DTC Detection Condition
Trouble Area
C1422
When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more.
  1. STOP fuse
  2. Stop light switch
  3. Stop light switch circuit
  4. Brake actuator assembly (Skid control ECU)
  5. Brake actuator assembly (Master cylinder pressure sensor)

WIRING DIAGRAM

Refer to DTC C1380 (RAV4_ACA30 RM000001N3L01AX_02.html).

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (RAV4_ACA30 RM000001K1O00SX.html).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
1.CHECK DTC

  1. Clear the DTCs (RAV4_ACA30 RM000000ONJ027X.html).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Depress the brake pedal.

  1. Check for DTCs (RAV4_ACA30 RM000000ONJ027X.html).

    Result:
    Result
    		Proceed to
    DTC C1422 is output
    		A
    DTCs C1422 and C1380 are output
    		B
    DTCs C1422 and C1425 are output
    		C


B
GO TO DTC C1380 (RAV4_ACA30 RM000001N3L01AX.html)

C
GO TO DTC C1425 (RAV4_ACA30 RM000000XIE04TX.html)
A


2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List mode on the intelligent tester (RAV4_ACA30 RM000000ONK01EX.html).

    ABS/VSC/TRC:
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Stop Light SW
    		Stop light switch / ON or OFF
    		ON: Brake pedal depressed
    OFF: Brake pedal released
    		-

  1. Check that the stop light condition observed on the intelligent tester changes according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.


NG
Go to step 5
OK


3.CHECK STOP LIGHT SWITCH INSTALLATION

  1. Check the brake pedal height and stop light switch installation (RAV4_ACA30 RM000001HJ300JX.html).

    OK:
    The brake pedal height and stop light switch installation are normal.


NG
INSPECT STOP LIGHT SWITCH (RAV4_ACA30 RM000001OCJ00QX.html)
OK


4.RECONFIRM DTC

  1. Clear the DTCs (RAV4_ACA30 RM000000ONJ027X.html).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform braking test (decelerate the vehicle by depressing the brake pedal).

  1. Check if the same DTC is output (RAV4_ACA30 RM000000ONJ027X.html).

    Result:
    Result
    		Proceed to
    DTC (C1422) is not output.
    		A
    DTC (C1422) is output.
    		B


B
REPLACE BRAKE ACTUATOR ASSEMBLY (RAV4_ACA30 RM000001XV200PX.html)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (RAV4_ACA30 RM00000135201PX.html)

5.INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL)


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Brake Control.Anti-Lock Brake System. Dtc C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction

  1. Make sure that there is no looseness in the locking part and connecting part of the connectors.

  1. Disconnect the stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    A66-2 - Body ground
    		Always
    		11 to 14 V


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


6.INSPECT STOP LIGHT SWITCH


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Brake Control.Anti-Lock Brake System. Dtc C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    1 - 2
    		Switch pin not pushed in
    		Below 1 Ω
    1 - 2
    		Switch pin pushed in
    		10 kΩ or higher


NG
REPLACE STOP LIGHT SWITCH (RAV4_ACA30 RM000003P9J002X.html)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (RAV4_ACA30 RM000001XV200OX.html)