Dtc C1210 Zero Point Calibration Of Yaw Rate Sensor Undone

Brake. Yaris. Ncp93, 131
Brake Control Dynamic Control Systems. Yaris. Ncp93, 131

DESCRIPTION

INSPECTION PROCEDURE

PERFORM ZERO POINT CALIBRATION OF YAW RATE AND DECELERATION SENSOR

PERFORM TEST MODE (SIGNAL CHECK)

CHECK YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)

READ VALUE USING TECHSTREAM (YAW RATE AND DECELERATION SENSOR)

DTC C1210 Zero Point Calibration of Yaw Rate Sensor Undone

DTC C1336 Zero Point Calibration of Acceleration Sensor Undone


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and deceleration sensor (airbag sensor assembly) via the CAN communication system.
The yaw rate and deceleration sensor (airbag sensor assembly) has a built-in deceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and deceleration sensor (airbag sensor assembly) and the CAN communication system, the DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output.
The DTCs are also output when the calibration has not been completed.

DTC No.
DTC Detection Condition
Trouble Area
C1210
Zero point calibration of yaw rate sensor undone.
  1. Yaw rate and deceleration sensor (Airbag sensor assembly)
  2. Skid control ECU (Brake actuator assembly)
C1336
Zero point calibration of acceleration sensor undone.
  1. Yaw rate and deceleration sensor (Airbag sensor assembly)
  2. Skid control ECU (Brake actuator assembly)

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (YARIS_NCP93 RM000000XHR078X.html).
HINT:
When U0124 and/or U0126 is output along with C1210 and/or C1336, inspect and repair trouble areas indicated by U0124 and/or U0126 first (YARIS_NCP93 RM000000YUO0EPX.html).
1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND DECELERATION SENSOR

  1. Perform zero point calibration of the yaw rate and deceleration sensor (YARIS_NCP93 RM000000XHR078X.html).


NEXT


2.PERFORM TEST MODE (SIGNAL CHECK)

  1. Turn the ignition switch off.

  1. Perform the sensor check in the Test Mode procedure (YARIS_NCP93 RM000000XHT098X.html).

    OK:
    All Test Mode DTCs are cleared.
    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (YARIS_NCP93 RM000000XHN0BRX.html).
Result
Result
Proceed to
NG
A
OK
B


B
END
A


3.CHECK YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)

  1. Turn the ignition switch off.

  1. Check that the yaw rate and deceleration sensor (airbag sensor assembly) has been installed properly (YARIS_NCP93 RM000000V6S02AX.html).

    OK:
    The sensor should be tightened to the specified torque.
    The sensor is not installed in a tilted position.


NG
INSTALL YAW RATE AND DECELERATION SENSOR CORRECTLY (AIRBAG SENSOR ASSEMBLY) (YARIS_NCP93 RM000000V6S02AX.html)
OK


4.READ VALUE USING TECHSTREAM (YAW RATE AND DECELERATION SENSOR)

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

  1. According to the display on the Techstream, read the Data List.

    ABS/VSC/TRAC (Skid Control ECU)
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Deceleration Sensor
    		Acceleration sensor/
    min.: -18.525 m/s2,
    max.: 18.387 m/s2
    		-
    		During deceleration/acceleration: Changes continuously
    Deceleration Sensor2
    		Acceleration sensor 2/
    min.: -18.525 m/s2,
    max.: 18.387 m/s2
    		-
    		During deceleration/acceleration: Changes continuously
    Yaw Rate Sensor
    		Yaw rate sensor/
    min.: -128°/s,
    max.: 127°/s
    		Vehicle stationary: 0°/s
    Right turn: -128 to 0°/s
    Left turn: 0 to 127°/s
    		-

  1. Check the yaw rate and deceleration sensor (airbag sensor assembly) output value displayed on the Techstream.

    OK:
    The yaw rate and deceleration sensor (airbag sensor assembly) output value is normal.
    NOTICE:
    Check the yaw rate and deceleration sensor (airbag sensor assembly) signal after replacement (YARIS_NCP93 RM000000XHT098X.html).
HINT:
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (YARIS_NCP93 RM000000XHN0BRX.html).


NG
REPLACE YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY) (YARIS_NCP93 RM000000V6U02AX.html)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (YARIS_NCP93 RM000001BXP02KX.html)