Dtc P1586 Acceleration Sensor Malfunction

Transmission. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
K111F Cvt. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK DTC OUTPUT (IN ADDITION TO DTC P1586)

READ VALUE USING INTELLIGENT TESTER (G SENSOR)

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

PERFORM INITIALIZATION

REPLACE YAW RATE SENSOR ASSEMBLY

PERFORM INITIALIZATION

REPLACE DECELERATION SENSOR

PERFORM INITIALIZATION

DTC P1586 Acceleration Sensor Malfunction


DESCRIPTION

  1. *1: w/ VSC
  2. *2: w/o VSC
The ECM determines the vehicle inclination based on a signal from the yaw rate sensor assembly*1 or deceleration sensor*2.
HINT:
If a CAN communication DTC is output, perform troubleshooting for that DTC first.

DTC Code
DTC Detection Condition
  1. Diagnosis Condition
  2. Malfunction Status
  3. Malfunction Time
  4. Other
Trouble Area
P1586
  1. The ignition switch is ON.
  2. With the vehicle speed 30 km/h (18 mph) or more, the difference between the longitudinal acceleration calculated based on the G sensor value and the longitudinal acceleration calculated based on the vehicle speed exceeds 0.35 G for 60 seconds or more.
  3. 3.0 seconds
  4. 1 trip detection logic
  1. Yaw rate sensor assembly (w/ VSC)
  2. Deceleration sensor (w/o VSC)
  3. Brake actuator assembly (Skid control ECU)
  1. The ignition switch is ON.
  2. No change detected in the yaw rate sensor assembly*1 or deceleration sensor*2 signal 16 times or more while the vehicle speed decreases from 30 km/h (18 mph) to 0 km/h (0 mph).
  3. 3.0 seconds
  4. 1 trip detection logic

WIRING DIAGRAM

Refer to DTC P1585 (RAV4_ACA30 RM000003UR800GX_05.html).

INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P1586)

  1. Clear the DTCs (RAV4_ACA30 RM000000W770KGX.html).

  1. Perform a road test where the vehicle is driven at 30 km/ h (18 mph) or more, the brakes are applied at least 16 times and the vehicle is finally stopped.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs using the tester.

    Result
    Result
    		Proceed to
    Only P1586 is output
    		A
    P1586 and other DTCs are output
    		B

    HINT:
    If any other DTCs besides DTC P1586 are output, perform troubleshooting for those DTCs first.


B
GO TO DTC CHART (RAV4_ACA30 RM0000030G903HX.html)
A


2.READ VALUE USING INTELLIGENT TESTER (G SENSOR)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. In accordance with the display on the tester, read the Data List.

    Engine and ECT
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    G sensor
    		Converted output voltage of yaw rate sensor assembly*1 or deceleration sensor*2/
    min.: 0 V
    max.: 5 V
    		Displays converted voltage of yaw rate sensor assembly*1 or deceleration sensor*2
    1. Vehicle on level ground: 2.31 V to 2.69 V
    2. Decelerating: 1.88 V to 2.5 V
    3. Accelerating: 2.5 V to 3.11 V
    4. G sensor malfunction: Set to 1.87 V
    5. Communication malfunction: Set to 1.87 V
    		-
    Result
    Result
    		Proceed to
    Data displayed is as specified under Normal Condition
    		A
    Data displayed is not as specified under Normal Condition (w/ VSC)
    		B
    Data displayed is not as specified under Normal Condition (w/o VSC)
    		C



B
Go to step 5

C
Go to step 7
A


3.REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

  1. Replace the brake actuator assembly (skid control ECU).

    1. w/ VSC (RAV4_ACA30 RM000001XV200PX.html).
    2. w/o VSC (RAV4_ACA30 RM000001XV200OX.html).

NEXT


4.PERFORM INITIALIZATION
NOTICE:
  1. Performing reset memory will clear the learned values of both the yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point calibration) and CVT oil pressure (CVT oil pressure calibration). Make sure to perform reset memory, yaw rate sensor assembly*1 or deceleration sensor*2 0 point calibration and CVT oil pressure calibration when replacing any of the parts shown in the following table:
    Replaced Part
    1. Continuously variable transaxle assembly
    2. ECM
    3. Oil pressure sensor
    4. Yaw rate sensor assembly (w/ VSC)
    5. Deceleration sensor (w/o VSC)
    6. Brake actuator assembly (skid control ECU)
  2. After performing reset memory, always perform yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point) calibration first, and then CVT oil pressure calibration.
  3. Always perform 0 point calibration with the vehicle on level ground.
  4. Do not shake or vibrate the vehicle during 0 point calibration.

  1. Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration (RAV4_ACA30 RM000003UQR002X.html).

  1. Check that no DTC is stored.


NEXT

END

5.REPLACE YAW RATE SENSOR ASSEMBLY

  1. Replace the yaw rate sensor assembly (RAV4_ACA30 RM000001XVQ009X.html).


NEXT


6.PERFORM INITIALIZATION
NOTICE:
  1. Performing reset memory will clear the learned values of both the yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point calibration) and CVT oil pressure (CVT oil pressure calibration). Make sure to perform reset memory, yaw rate sensor assembly*1 or deceleration sensor*2 0 point calibration and CVT oil pressure calibration when replacing any of the parts shown in the following table:
    Replaced Part
    1. Continuously variable transaxle assembly
    2. ECM
    3. Oil pressure sensor
    4. Yaw rate sensor assembly (w/ VSC)
    5. Deceleration sensor (w/o VSC)
    6. Brake actuator assembly (skid control ECU)
  2. After performing reset memory, always perform yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point) calibration first, and then CVT oil pressure calibration.
  3. Always perform 0 point calibration with the vehicle on level ground.
  4. Do not shake or vibrate the vehicle during 0 point calibration.

  1. Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration (RAV4_ACA30 RM000003UQR002X.html).

  1. Check that no DTC is stored.


NEXT

END

7.REPLACE DECELERATION SENSOR

  1. Replace the deceleration sensor (RAV4_ACA30 RM000001XVQ009X.html).


NEXT


8.PERFORM INITIALIZATION
NOTICE:
  1. Performing reset memory will clear the learned values of both the yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point calibration) and CVT oil pressure (CVT oil pressure calibration). Make sure to perform reset memory, yaw rate sensor assembly*1 or deceleration sensor*2 0 point calibration and CVT oil pressure calibration when replacing any of the parts shown in the following table:
    Replaced Part
    1. Continuously variable transaxle assembly
    2. ECM
    3. Oil pressure sensor
    4. Yaw rate sensor assembly (w/ VSC)
    5. Deceleration sensor (w/o VSC)
    6. Brake actuator assembly (skid control ECU)
  2. After performing reset memory, always perform yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point) calibration first, and then CVT oil pressure calibration.
  3. Always perform 0 point calibration with the vehicle on level ground.
  4. Do not shake or vibrate the vehicle during 0 point calibration.

  1. Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration (RAV4_ACA30 RM000003UQR002X.html).

  1. Check that no DTC is stored.


NEXT

END