Brake. Camry. Acv40 Gsv40
Brake Control. Camry. Acv40 Gsv40
Vehicle Stability Control System -- Problem Symptoms Table |
If there are no DTCs output and the problem still occurs, check the circuits for each problem symptom in the order given in the table below and proceed to the relevant troubleshooting page.
- HINT:
- Inspect the fuse and relay before investigating the suspected areas as shown in the table below.
- Inspect each malfunction circuit in numerical order for the corresponding symptom.
| Symptom | Suspected Area | See page |
| ABS, BA and/or EBD does not operate | 1. Check the DTC again and make sure that the normal system code is output. | CAMRY_ACV40 RM000000XHV08UX.html |
| 2. IG power source circuit | CAMRY_ACV40 RM000000XW608VX.html | |
| 3. Front speed sensor circuit | CAMRY_ACV40 RM000000XI90DPX.html | |
| 4. Rear speed sensor circuit | CAMRY_ACV40 RM000000XIA0AOX.html | |
| 5. Check the brake actuator assembly with the intelligent tester. (Check brake actuator assembly operation using the Active Test function.) If abnormal, check the hydraulic circuit for leakage. | CAMRY_ACV40 RM0000013P9007X.html | |
| 6. If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | CAMRY_ACV40 RM0000013P6006X.html | |
| ABS, BA and/or EBD does not operate efficiently | 1. Check the DTC again and make sure that the normal system code is output. | CAMRY_ACV40 RM000000XHV08UX.html |
| 2. Front speed sensor circuit | CAMRY_ACV40 RM000000XI90DPX.html | |
| 3. Rear speed sensor circuit | CAMRY_ACV40 RM000000XIA0AOX.html | |
| 4. Stop light switch circuit | CAMRY_ACV40 RM000000XIE0B6X.html | |
| 5. Check the brake actuator assembly with the intelligent tester. (Check brake actuator assembly operation using the Active Test function.) If abnormal, check the hydraulic circuit for leakage. | CAMRY_ACV40 RM0000013P9007X.html | |
| 6. If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | CAMRY_ACV40 RM0000013P6006X.html | |
| ABS sensor DTC check cannot be done | 1. Check the DTC again and make sure that the normal system code is output. | CAMRY_ACV40 RM000000XHV08UX.html |
| 2. TC and CG terminal circuit | CAMRY_ACV40 RM000000XIU0ADX.html | |
| 3. If the symptoms still occur even after the above circuit in suspected areas has been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | CAMRY_ACV40 RM0000013P6006X.html | |
| ABS warning light abnormal (Remains on) | 1. ABS warning light circuit | CAMRY_ACV40 RM000000XIH095X.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| ABS warning light abnormal (Does not come on) | 1. ABS warning light circuit | CAMRY_ACV40 RM000000XIQ094X.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| BRAKE warning light abnormal (Remains on) | 1. BRAKE warning light circuit | CAMRY_ACV40 RM000000YHG096X.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| BRAKE warning light abnormal (Does not come on) | 1. BRAKE warning light circuit | CAMRY_ACV40 RM000000YHH096X.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| VSC and/or TRC does not operate | 1. Check the DTC again and make sure that the normal system code is output. | CAMRY_ACV40 RM000000XHV08UX.html |
| 2. IG power source circuit | CAMRY_ACV40 RM000000XW608VX.html | |
| 3. Check the hydraulic circuit for leakage | - | |
| 4. Front speed sensor circuit | CAMRY_ACV40 RM000000XI90DPX.html | |
| 5. Rear speed sensor circuit | CAMRY_ACV40 RM000000XIA0AOX.html | |
| 6. Yaw rate and acceleration sensor circuit | CAMRY_ACV40 RM000001RFV07HX.html | |
| 7. Steering angle sensor circuit | CAMRY_ACV40 RM000000XIM0APX.html | |
| 8. If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | CAMRY_ACV40 RM0000013P6006X.html | |
| VSC sensor DTC check cannot be done | 1. Check the DTC again and make sure that the normal system code is output. | CAMRY_ACV40 RM000000XHV08UX.html |
| 2. TC and CG terminal circuit | CAMRY_ACV40 RM000000XIU0ADX.html | |
| 3. If the symptoms still occur even after the above circuit in suspected areas has been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | CAMRY_ACV40 RM0000013P6006X.html | |
| SLIP indicator light abnormal (Remains on) | 1. SLIP indicator light circuit | CAMRY_ACV40 RM000000YHI06SX.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| SLIP indicator light abnormal (Does not come on) | 1. SLIP indicator light circuit | CAMRY_ACV40 RM000000YHJ06SX.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| Sensor check cannot be done | 1. TS and CG terminal circuit | CAMRY_ACV40 RM000000XIV087X.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html |