Dtc B2417 Headlight Beam Level Control Motor Lh Malfunction
Lighting. Lexus Is250, Is220D. Gse20 Ale20
DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
PERFORM ACTIVE TEST BY INTELLIGENT TESTER
CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING MOTOR - AFS ECU)
CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING MOTOR - HEADLIGHT ASSEMBLY)
INSPECT HEADLIGHT LEVELING MOTOR (LH AND/OR RH)
DTC B2417 Headlight Beam Level Control Motor LH Malfunction |
DTC B2418 Headlight Beam Level Control Motor RH Malfunction |
DESCRIPTION
The leveling actuator (headlight leveling motor) receives a signal from the AFS ECU to operate. The AFS ECU receives signals regarding the operating conditions of the leveling actuator (headlight leveling motor).DTC No.
| DTC Detection Condition
| Trouble Area
|
B2417
| - Malfunction in headlight leveling motor LH
- Open or short in headlight leveling motor LH circuit
| - Headlight leveling motor LH (Headlight assembly LH)
- Wire harness or connector
- AFS ECU
|
B2418
| - Malfunction in headlight beam level control motor RH
- Open or short in headlight beam level control motor RH circuit
| - Headlight leveling motor RH (Headlight assembly RH)
- Wire harness or connector
- AFS ECU
|
WIRING DIAGRAM
INSPECTION PROCEDURE
1.PERFORM ACTIVE TEST BY INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester main switch on.
Select the "ACTIVE TEST" on the intelligent tester.
Check the headlight leveling motor operation with the intelligent tester.
ACTIVE TEST: AFS (AFS ECU)Item
| Test Details
| Diagnostic Note
|
Drive The Leveling Motor
| Drive the leveling motor UP / OFF
| -
|
Drive The Leveling Motor
| Drive the leveling motor DOWN / OFF
| -
|
- OK:
- Headlight leveling motor is operated.
- Result:
Result
| Proceed to
|
OK (When checking from PROBLEM SYMPTOMS TABLE)
| A
|
OK (When checking from DIAGNOSTIC TROUBLE CODE CHART)
| B
|
NG
| C
|
A |
|
|
|
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE |
|
2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING MOTOR - AFS ECU) |
Disconnect the B12 and B2 headlight assembly connectors.
Disconnect the A28 AFS ECU connector.
Measure the resistance according to the value (s) in the table below.
- Standard resistance:
- LH Side (B2417):
Tester Connection
| Condition
| Specified Condition
|
A28-29 (LL1+) - B12-15 (LL1+)
| Always
| Below 1 Ω
|
A28-30 (LL1-) - B12-14 (LL1-)
| Always
| Below 1 Ω
|
A28-31 (LL2+) - B12-13 (LL2+)
| Always
| Below 1 Ω
|
A28-32 (LL2-) - B12-12 (LL2-)
| Always
| Below 1 Ω
|
A28-29 (LL1+) - Body ground
| Always
| 10 kΩ or higher
|
A28-30 (LL1-) - Body ground
| Always
| 10 kΩ or higher
|
A28-31 (LL2+) - Body ground
| Always
| 10 kΩ or higher
|
A28-32 (LL2-) - Body ground
| Always
| 10 kΩ or higher
|
- RH Side (B2418):
Tester Connection
| Condition
| Specified Condition
|
A28-13 (LR1+) - B2-15 (LR1+)
| Always
| Below 1 Ω
|
A28-14 (LR1-) - B2-14 (LR1-)
| Always
| Below 1 Ω
|
A28-15 (LR2+) - B2-13 (LR2+)
| Always
| Below 1 Ω
|
A28-16 (LR2-) - B2-12 (LR2-)
| Always
| Below 1 Ω
|
A28-13 (LR1+) - Body ground
| Always
| 10 kΩ or higher
|
A28-14 (LR1-) - Body ground
| Always
| 10 kΩ or higher
|
A28-15 (LR2+) - Body ground
| Always
| 10 kΩ or higher
|
A28-16 (LR2-) - Body ground
| Always
| 10 kΩ or higher
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING MOTOR - HEADLIGHT ASSEMBLY) |
Disconnect the headlight leveling motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- LH Side:
Tester Connection
| Condition
| Specified Condition
|
B12-15 (LL1+) - 3
| Always
| Below 1 Ω
|
B12-14 (LL1-) - 4
| Always
| Below 1 Ω
|
B12-13 (LL2+) - 1
| Always
| Below 1 Ω
|
B12-12 (LL2-) - 2
| Always
| Below 1 Ω
|
B12-15 (LL1+) - Body ground
| Always
| 10 kΩ or higher
|
B12-14 (LL1-) - Body ground
| Always
| 10 kΩ or higher
|
B12-13 (LL2+) - Body ground
| Always
| 10 kΩ or higher
|
B12-12 (LL2-) - Body ground
| Always
| 10 kΩ or higher
|
- RH Side:
Tester Connection
| Condition
| Specified Condition
|
B2-15 (LR1+) - 3
| Always
| Below 1 Ω
|
B2-14 (LR1-) - 4
| Always
| Below 1 Ω
|
B2-13 (LR2+) - 1
| Always
| Below 1 Ω
|
B2-12 (LR2-) - 2
| Always
| Below 1 Ω
|
B2-15 (LR1+) - Body ground
| Always
| 10 kΩ or higher
|
B2-14 (LR1-) - Body ground
| Always
| 10 kΩ or higher
|
B2-13 (LR2+) - Body ground
| Always
| 10 kΩ or higher
|
B2-12 (LR2-) - Body ground
| Always
| 10 kΩ or higher
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
4.INSPECT HEADLIGHT LEVELING MOTOR (LH AND/OR RH) |
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- RH Side (B2418):
Tester Connection
| Condition
| Specified Condition
|
1 - 2
| Always
| 5.8 to 12.5 Ω
|
3 - 4
| Always
| 5.8 to 12.5 Ω
|
- LH Side (B2417):
Tester Connection
| Condition
| Specified Condition
|
1 - 2
| Always
| 5.8 to 12.5 Ω
|
3 - 4
| Always
| 5.8 to 12.5 Ω
|
| REPLACE HEADLIGHT ASSEMBLY LH OR HEADLIGHT ASSEMBLY RH |
|
|