Parking Brake Lever -- Installation |
| 1. INSTALL PARKING BRAKE SWITCH ASSEMBLY |
Install the parking brake switch assembly to the parking brake lever sub-assembly with the screw.
- Torque:
- 0.9 N*m{9 kgf*cm, 8 in.*lbf}
 |
| 2. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY |
Pass the No. 1 parking brake cable assembly through the parking brake lever sub-assembly.
 |
Bend the parking brake lever claw.
 |
Temporarily install the adjusting nut and the lock nut to the No. 1 parking brake cable assembly.
 |
| 3. INSTALL PARKING BRAKE CABLE END STOPPER |
Install the parking brake cable end stopper to the No. 1 parking brake cable assembly.
 |
| 4. INSTALL PARKING BRAKE EQUALIZER |
Engage the 2 claws to install the parking brake equalizer to the parking brake cable end stopper.
 |
Engage the 2 claws to install the parking brake cable end stopper to the No. 1 parking brake cable assembly.
 |
| 5. INSTALL PARKING BRAKE LEVER ASSEMBLY |
Install the parking brake lever assembly with the 2 bolts.
- Torque:
- 15 N*m{148 kgf*cm, 11 ft.*lbf}
 |
Connect the parking brake switch connector.
 |
| 6. CONNECT PARKING BRAKE EQUALIZER |
Connect the parking brake equalizer to the No. 3 parking brake cable assembly as shown in the illustration.
 |
Connect the parking brake equalizer to the No. 2 parking brake cable assembly.
- HINT:
- Perform the same procedure for the No. 3 parking brake cable assembly.
| 7. INSTALL NO. 3 BELT ANCHOR REINFORCEMENT SUB-ASSEMBLY |
Install the No. 3 belt anchor reinforcement sub-assembly with the 5 bolts.
- Torque:
- 27 N*m{275 kgf*cm, 19 ft.*lbf}
 |
Install the floor carpet.
| 8. INSTALL NO. 2 BELT ANCHOR REINFORCEMENT SUB-ASSEMBLY |
Install the No. 2 belt anchor reinforcement sub-assembly with the 4 bolts.
- Torque:
- 27 N*m{275 kgf*cm, 19 ft.*lbf}
 |
| 9. ADJUST PARKING BRAKE LEVER TRAVEL |
Remove the upper console box assembly (COROLLA_ZRE142 RM000002XV501QX.html).
Completely release the parking brake lever.
Loosen the lock nut and the adjusting nut to completely release the parking brake cable.
 |
Fully depress the brake lever 3 to 5 times with the engine stopped.
Turn the adjusting nut until the parking brake lever travel is corrected to within the specified range.
- Parking brake lever travel:
- 6 to 9 notches at 200 N (20 kgf, 45.0 lbf)
Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.
- Torque:
- 6.0 N*m{61 kgf*cm, 53 in.*lbf}
Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.
Check whether the parking brake drags or not.
Install the upper console box assembly (COROLLA_ZRE142 RM000002XV301QX.html).
| 10. INSPECT BRAKE WARNING LIGHT |
When operating the parking brake lever, check that the brake warning light illuminates.
- Standard:
- The brake warning light always illuminates at the first click.
| 11. INSTALL CONSOLE BOX ASSEMBLY |
- HINT:
- Refer to the instructions for Installation of the front console box (Link).
| 12. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat) |
- HINT:
- Refer to the instructions for Installation of the front seat assembly (COROLLA_ZRE142 RM000000Z8T0D2X.html).
| 13. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat) |
- HINT:
- Refer to the instructions for Installation of the front seat assembly (COROLLA_ZRE142 RM000000Z8T0D1X.html).
| 14. INSTALL FRONT SEAT ASSEMBLY RH |
- HINT:
- Perform the same procedure for the LH side.
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag) |
| 16. INSPECT SRS WARNING LIGHT (w/ Front Seat Side Airbag) |
- HINT: