Dtc C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction

Brake. Camry. Acv40 Gsv40
Brake Control. Camry. Acv40 Gsv40

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)

PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

INSPECT SPEED SENSOR SIGNAL WAVEFORM

RECONFIRM DTC

INSPECT SPEED SENSOR INSTALLATION

INSPECT REAR SPEED SENSOR

CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE TO SKID CONTROL ECU)

CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE TO REAR SPEED SENSOR)

INSPECT SPEED SENSOR SIGNAL WAVEFORM

READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)

RECONFIRM DTC

INSPECT SPEED SENSOR ROTOR

DTC C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction

DTC C0215/34 Left Rear Wheel Speed Sensor Signal Malfunction

DTC C1273/73 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC C1274/74 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC C1332/38 Right Rear Speed Sensor Circuit

DTC C1333/39 Left Rear Speed Sensor Circuit


DESCRIPTION

Refer to DTCs C0200/31, C0205/32, C1330/35, and C1331/36 (Link).
DTCs from C1273/73 to C1278/78 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs from C1273/73 to C1278/78 are output only in the test mode.

DTC No.
DTC Detecting Condition
Trouble Area
C0210/33
C0215/34
When either of the following is detected:
  1. Vehicle speed is more than 40 km/h (25 mph), and pulses are not input for 0.03 sec.
  2. When the vehicle speed has reached 12 km/h (8 mph), after the initial start or restart a wheel speed of 0 km/h (0 mph) is detected.
  1. Rear speed sensor RH and/or LH
  2. Rear speed sensor circuit RH and/or LH
  3. Rear speed sensor rotor RH and/or LH
  4. Sensor installation
  5. Brake actuator assembly (skid control ECU)
C1332/38
C1333/39
Abnormality in the resistance value of each speed sensor is detected.
  1. Rear speed sensor RH and/or LH
  2. Rear speed sensor circuit RH and/or LH
  3. Sensor installation
C1273/73
C1274/74
Detected only during test mode.
  1. Rear speed sensor
  2. Sensor installation
  3. Sensor rotor
C1277/77
C1278/78
Detected only during test mode.
  1. Rear speed sensor
  2. Sensor installation
  3. Sensor rotor
HINT:
DTC No. C0210/33 and C1332/38 are for the rear speed sensor RH.
DTC No. C0215/34 and C1333/39 are for the rear speed sensor LH.

WIRING DIAGRAM


Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System. Dtc C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction


INSPECTION PROCEDURE

HINT:
Check the condition of each related circuit connector before troubleshooting (CAMRY_ACV40 RM000000UZ301ZX.html).
1.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select "Data List" and read the value displayed on the intelligent tester (CAMRY_ACV40 RM000001JBA003X.html).

    Data List: ABS
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    RR Wheel Speed
    		Wheel speed sensor (RR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    		Actual wheel speed
    RL Wheel Speed
    		Wheel speed sensor (RL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    		Actual wheel speed

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.


NG
Go to step 5
OK


2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

  1. Check if test mode (signal check) DTCs are detected (CAMRY_ACV40 RM000001JBD01XX.html).

    Result:

    Condition
    		Proceed to
    Test mode (signal check) DTC is not output
    		A
    Test mode (signal check) DTC is output
    		B


B
Go to step 5
A


3.INSPECT SPEED SENSOR SIGNAL WAVEFORM


    Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System. Dtc C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction

  1. Lift up the vehicle.

  1. Perform the inspection using an oscilloscope.

    1. Disconnect the skid control ECU connector.

    2. Connect the oscilloscope to terminals of the skid control ECU.

    3. Check that a waveform is output when the tires are rotated.

      OK:
      The same waveform is output from rear wheels and there is no noise or interference in the waveform.
      HINT:
      1. As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the output voltage becomes greater.
      2. When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.

    4. Connect the connector.



NG
CLEAN OR REPLACE SPEED SENSOR AND SENSOR ROTOR
OK


4.RECONFIRM DTC

  1. Clear the DTCs (CAMRY_ACV40 RM000001JB800LX.html).

  1. Drive the vehicle at a speed of approximately 40 km/h (25 mph) or more for 60 seconds or more.

  1. Check if the same DTCs are recorded (CAMRY_ACV40 RM000001JB800LX.html).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.

    Result:

    Condition
    		Proceed to
    DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are output
    		A
    DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    		B
    DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are not output (When troubleshooting in accordance with the DTC CHART)
    		C


B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (CAMRY_ACV40 RM000001JB500KX.html)

C
END
A


5.INSPECT SPEED SENSOR INSTALLATION


    Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System. Dtc C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction

  1. Check the rear speed sensor installation.

    OK:
    There is no clearance between the sensor and rear axle carrier.
    NOTICE:
    Check the speed sensor signal after replacement (CAMRY_ACV40 RM000001JBD01XX.html).


NG
REPLACE REAR SPEED SENSOR (CAMRY_ACV40 RM0000011P900SX.html)
OK


6.INSPECT REAR SPEED SENSOR


    Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System. Dtc C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction

  1. Disconnect the rear speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH:
    Tester Connection
    		Specified Condition
    g1-1 (RL+) - g1-2 (RL-)
    		Below 2.2 kΩ
    g1-1 (RL+) - Body ground
    		10 kΩ or higher
    g1-2 (RL-) - Body ground
    		10 kΩ or higher
    RH:
    Tester Connection
    		Specified Condition
    f1-1 (RR+) - f1-2 (RR-)
    		Below 2.2 kΩ
    f1-1 (RR+) - Body ground
    		10 kΩ or higher
    f1-2 (RR-) - Body ground
    		10 kΩ or higher
NOTICE:
Check the speed sensor signal after replacement (CAMRY_ACV40 RM000001JBD01XX.html).


NG
REPLACE REAR SPEED SENSOR (CAMRY_ACV40 RM0000011P900SX.html)
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE TO SKID CONTROL ECU)


    Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System. Dtc C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction

  1. Check harness and connector.

    1. Disconnect the skid control ECU connector.

    2. Disconnect the skid control sensor wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      LH:
      Tester Connection
      		Specified Condition
      A25-7 (RL+) - g1-1 (RL+)
      		Below 1 Ω
      A25-17 (RL-) - g1-2 (RL-)
      		Below 1 Ω
      g1-1 (RL+) - Body ground
      		10 kΩ or higher
      g1-2 (RL-) - Body ground
      		10 kΩ or higher
      RH:
      Tester Connection
      		Specified Condition
      A25-19 (RR+) - f1-1 (RR+)
      		Below 1 Ω
      A25-8 (RR-) - f1-2 (RR-)
      		Below 1 Ω
      f1-1 (RR+) - Body ground
      		10 kΩ or higher
      f1-2 (RR-) - Body ground
      		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU TO SKID CONTROL SENSOR WIRE)
OK


8.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE TO REAR SPEED SENSOR)


    Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System. Dtc C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction

  1. Check harness and connector (skid control sensor wire).

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      LH:
      Tester Connection
      		Specified Condition
      g1-1 - A-1
      		Below 1 Ω
      g1-1 - A-2
      		10 kΩ or higher
      g1-1 - Body ground
      		10 kΩ or higher
      g1-2 - A-2
      		Below 1 Ω
      g1-2 - A-1
      		10 kΩ or higher
      g1-2 - Body ground
      		10 kΩ or higher
      RH:
      Tester Connection
      		Specified Condition
      f1-1 - A-1
      		Below 1 Ω
      f1-1 - A-2
      		10 kΩ or higher
      f1-1 - Body ground
      		10 kΩ or higher
      f1-2 - A-2
      		Below 1 Ω
      f1-2 - A-1
      		10 kΩ or higher
      f1-2 - Body ground
      		10 kΩ or higher


NG
REPAIR OR REPLACE SKID CONTROL SENSOR WIRE
OK


9.INSPECT SPEED SENSOR SIGNAL WAVEFORM


    Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System. Dtc C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction

  1. Lift up the vehicle.

  1. Perform the inspection using the oscilloscope.

    1. Disconnect the skid control ECU connector.

    2. Connect the oscilloscope to terminals of the skid control ECU.

    3. Check that a waveform is output when the tires are rotated.

      OK:
      The same waveforms is output from rear wheels and there is no noise or interference in the waveform.
      HINT:
      1. As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the output voltage becomes greater.
      2. When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.

    4. Connect the connectors.



NG
CLEAN OR REPLACE SPEED SENSOR AND SENSOR ROTOR
OK


10.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select "Data List" and read the value displayed on the intelligent tester (CAMRY_ACV40 RM000001JBA003X.html).

    Data List: ABS
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    RR Wheel Speed
    		Wheel speed sensor (RR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    		Actual wheel speed
    RL Wheel Speed
    		Wheel speed sensor (RL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    		Actual wheel speed

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.
    HINT:
    1. It is suspected that the DTCs were output due to a bad connection of the connector terminal.
    2. If troubleshooting has been carried out according to the "PROBLEM SYMPTOMS TABLE", refer back to the table and proceed to the next step (CAMRY_ACV40 RM000001JB500KX.html).


NG
REPLACE BRAKE ACTUATOR ASSEMBLY (CAMRY_ACV40 RM0000013P6007X.html)
OK


11.RECONFIRM DTC

  1. Clear the DTCs (CAMRY_ACV40 RM000001JB800LX.html).

  1. Drive the vehicle at a speed of approximately 40 km/h (25 mph) or more for 60 seconds or more.

  1. Check if the same DTCs are recorded (CAMRY_ACV40 RM000001JB800LX.html).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.

    Result:

    Condition
    		Proceed to
    DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are output
    		A
    DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are not output
    		B


B
END
A


12.INSPECT SPEED SENSOR ROTOR

  1. Turn the ignition switch off.

  1. Remove the rear axle (CAMRY_ACV40 RM000001IXL002X.html).

  1. Check the rotor.

    OK:
    No scratches, cracks, oil, or foreign matter on the rotors.
    NOTICE:
    Check the speed sensor signal after cleaning or replacement (CAMRY_ACV40 RM000001JBD01XX.html).

  1. Install the rear axle (CAMRY_ACV40 RM000001IXJ00XX.html).



NG
CLEAN OR REPLACE SPEED SENSOR ROTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (CAMRY_ACV40 RM0000013P6007X.html)