READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF)
CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH, BATTERY AND BODY GROUND)
DTC B2342 Switch Failure |
DESCRIPTION
This DTC is stored when the sliding roof drive gear sub-assembly detects that the sliding roof switch in the map light assembly is stuck for 30 seconds or more.| DTC Code | DTC Detection Condition | Trouble Area |
| B2342 | The sliding roof drive gear sub-assembly detects that the sliding roof switch in the map light assembly is stuck for 30 seconds or more. |
|
WIRING DIAGRAM
INSPECTION PROCEDURE
- NOTICE:
- When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (LandCruiser RM000001VJR08IX.html).
| 1.CHECK FOR DTC |
Clear the DTCs (LandCruiser RM000001YIS044X.html).
Check for DTCs (LandCruiser RM000001YIS044X.html).
Result Result Proceed to DTC B2342 is output A DTC B2342 is not output B
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF) |
Using the intelligent tester, read the Data List (LandCruiser RM000000UZR094X.html).
Sliding Roof Tester Display Measurement Item/Range Normal Condition Diagnostic Note Open Switch Failure (Past) Slide open switch failure signal (Past) / ON or OFF ON: Slide open switch signal failure (Past)
OFF: No slide open switch signal failure (Past)- Close Switch Failure (Past) Slide close switch failure signal (Past) / ON or OFF ON: Slide close switch signal failure (Past)
OFF: No slide close switch signal failure (Past)- Up Switch Failure (Past) Tilt up switch failure signal (Past) / ON or OFF ON: Tilt up switch signal failure (Past)
OFF: No tilt up switch signal failure (Past)- Down Switch Failure (Past) Tilt down switch failure signal (Past) / ON or OFF ON: Tilt down switch signal failure (Past)
OFF: No tilt down switch signal failure (Past)- Open Switch Failure (Current) Slide open switch failure signal (Current) / ON or OFF ON: Slide open switch signal failure (Current)
OFF: No slide open switch signal failure (Current)- Close Switch Failure (Current) Slide close switch failure signal (Current) / ON or OFF ON: Slide close switch signal failure (Current)
OFF: No slide close switch signal failure (Current)- Up Switch Failure (Current) Tilt up switch failure signal (Current) / ON or OFF ON: Tilt up switch signal failure (Current)
OFF: No tilt up switch signal failure (Current)- Down Switch Failure (Current) Tilt down switch failure signal (Current) / ON or OFF ON: Tilt down switch signal failure (Current)
OFF: No tilt down switch signal failure (Current)- - OK:
- "OFF" appears on the intelligent tester screen.
|
| ||||
| OK | ||
| ||
| 3.INSPECT MAP LIGHT ASSEMBLY |
 |
Remove the map light assembly (LandCruiser RM000003YO9019X.html).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Switch Condition Specified Condition 8 (IG) - 23 (IG3) Always Below 1 Ω 24 (UP) - 5 (GND3) Tilt up switch pressed Below 1 Ω 24 (UP) - 5 (GND3) Tilt up switch not pressed 10 kΩ or higher 25 (DOWN) - 5 (GND3) Tilt down switch pressed Below 1 Ω 25 (DOWN) - 5 (GND3) Tilt down switch not pressed 10 kΩ or higher 27 (OPN) - 5 (GND3) Slide open switch pressed Below 1 Ω 27 (OPN) - 5 (GND3) Slide open switch not pressed 10 kΩ or higher 28 (CLS) - 5 (GND3) Slide close switch pressed Below 1 Ω 28 (CLS) - 5 (GND3) Slide close switch not pressed 10 kΩ or higher
Text in Illustration *a Component without harness connected
(Map Light Assembly)
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH, BATTERY AND BODY GROUND) |
Disconnect the W2 ECU connector.
Disconnect the W7 switch connector.
Measure the resistance and voltage according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition W2-10 (UP) - W7-24 (UP) Always Below 1 Ω W2-8 (DWN) - W7-25 (DOWN) Always Below 1 Ω W2-7 (OPN) - W7-27 (OPN) Always Below 1 Ω W2-9 (CLS) - W7-28 (CLS) Always Below 1 Ω W7-5 (GND3) - Body ground Always Below 1 Ω W2-2 (E) - Body ground Always Below 1 Ω W2-5 (IG) - W7-23 (IG3) Always Below 1 Ω W2-10 (UP) or W7-24 (UP) - Body ground Always 10 kΩ or higher W2-8 (DWN) or W7-25 (DOWN) - Body ground Always 10 kΩ or higher W2-7 (OPN) or W7-27 (OPN) - Body ground Always 10 kΩ or higher W2-9 (CLS) or W7-28 (CLS) - Body ground Always 10 kΩ or higher W2-5 (IG) or W7-23 (IG3) - Body ground Always 10 kΩ or higher
- Standard Voltage:
Tester Connection Switch Condition Specified Condition W7-8 (IG) - Body ground Ignition switch off Below 1 V W7-8 (IG) - Body ground Ignition switch ON 11 to 14 V
|
| ||||
| OK | ||
| ||