Sliding Roof System Data List / Active Test

  1. READ DATA LIST

  1. PERFORM ACTIVE TEST

Sliding Roof System -- Data List / Active Test



READ DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Sliding Roof / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Sliding Roof
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Open Switch
    		Slide open switch signal / ON or OFF
    		ON: Slide open switch pressed
    OFF: Slide open switch not pressed
    		-
    Close Switch
    		Slide close switch signal / ON or OFF
    		ON: Slide close switch pressed
    OFF: Slide close switch not pressed
    		-
    Up Switch
    		Tilt up switch signal / ON or OFF
    		ON: Tilt up switch pressed
    OFF: Tilt up switch not pressed
    		-
    Down Switch
    		Tilt down switch signal / ON or OFF
    		ON: Tilt down switch pressed
    OFF: Tilt down switch not pressed
    		-
    Hall IC1 Pulse
    		Hall IC1 pulse output / Lo or Hi
    		Lo and Hi repeat during motor operation
    		Lo: Hall IC1 output is low.
    Hi: Hall IC1 output is high.
    Hall IC1 Status
    		Status of Hall IC1 / Normal or Error
    		Normal: Hall IC1 normal
    Error: Hall IC1 not normal
    		-
    Hall IC2 Pulse
    		Hall IC2 pulse output / Lo or Hi
    		Lo and Hi repeat during motor operation
    		Lo: Hall IC2 output is low.
    Hi: Hall IC2 output is high.
    Hall IC2 Status
    		Status of Hall IC2 / Normal or Error
    		Normal: Hall IC2 normal
    Error: Hall IC2 not normal
    		-
    Ignition (Direct Signal)
    		Ignition switch signal / ON or OFF
    		ON: Ignition switch ON
    OFF: Ignition switch off
    		-
    Ignition (MPX)
    		Ignition switch signal (LIN signal) / ON or OFF
    		ON: Ignition switch ON
    OFF: Ignition switch off
    		-
    Door Courtesy
    		Driver side door courtesy light switch signal / ON or OFF
    		ON: Driver side door open
    OFF: Driver side door closed
    		-
    Door Key Close Operation
    		Key-linked sliding roof close signal / ON or OFF
    		ON: Driver side door key cylinder turned to lock position using key
    OFF: Driver side door key cylinder not turned
    		-
    Door Key Open Operation
    		Key-linked sliding roof open signal / ON or OFF
    		ON: Driver side door key cylinder turned to unlock position using key
    OFF: Driver side door key cylinder not turned
    		-
    Wireless Close Operation
    		Wireless sliding roof close signal / ON or OFF
    		ON: Transmitter LOCK switch pressed and held
    OFF: Transmitter LOCK switch not pressed
    		-
    Wireless Open Operation
    		Wireless sliding roof open signal / ON or OFF
    		ON: Transmitter UNLOCK switch pressed and held
    OFF: Transmitter UNLOCK switch not pressed
    		-
    Key Off Permission
    		Key-off operation permit signal / ON or OFF
    		ON: Driver side door not closed within 43 seconds after ignition switch turned off
    OFF: Any status except "ON" status
    		-
    Door Key Related (Open)
    		Key-linked sliding roof open operation status / Avail or Not Avl
    		Avail: Key-linked sliding roof open operation available
    Not Avl: Key-linked sliding roof open operation not available
    		Customize function.
    Door Key Related (Close)
    		Key-linked sliding roof close operation status / Avail or Not Avl
    		Avail: Key-linked sliding roof close operation available
    Not Avl: Key-linked sliding roof close operation not available
    		Customize function.
    Wireless Key Rel (Open)
    		Wireless transmitter-linked sliding roof open operation status / Avail or Not Avl
    		Avail: Wireless transmitter-linked sliding roof open operation available
    Not Avl: Wireless transmitter-linked sliding roof open operation not available
    		Customize function.
    Wireless Key Rel (Close)
    		Wireless transmitter-linked sliding roof close operation status / Avail or Not Avl
    		Avail: Wireless transmitter-linked sliding roof close operation available
    Not Avl: Wireless transmitter-linked sliding roof close operation not available
    		Customize function.
    Door Key Related Operation
    		Direction for key-linked operation / Tilt or Slide
    		Tilt: Key-linked sliding roof operation operates tilt up or down
    Slide: Key-linked sliding roof operation operates slide open or close
    		Customize function.
    Wireless Key Rel Operation
    		Direction for wireless transmitter-linked operation / Tilt or Slide
    		Tilt: Wireless transmitter-linked sliding roof operation operates tilt up or down
    Slide: Wireless transmitter-linked sliding roof operation operates slide open or close
    		Customize function.
    Open Switch Failure (Past)
    		Slide open switch failure signal (Past) / ON or OFF
    		ON: Slide open switch signal failure (Past)
    OFF: No slide open switch signal failure (Past)
    		-
    Close Switch Failure (Past)
    		Slide close switch failure signal (Past) / ON or OFF
    		ON: Slide close switch signal failure (Past)
    OFF: No slide close switch signal failure (Past)
    		-
    Up Switch Failure (Past)
    		Tilt up switch failure signal (Past) / ON or OFF
    		ON: Tilt up switch signal failure (Past)
    OFF: No tilt up switch signal failure (Past)
    		-
    Down Switch Failure (Past)
    		Tilt down switch failure signal (Past) / ON or OFF
    		ON: Tilt down switch signal failure (Past)
    OFF: No tilt down switch signal failure (Past)
    		-
    Open Switch Failure (Current)
    		Slide open switch failure signal (Current) / ON or OFF
    		ON: Slide open switch signal failure (Current)
    OFF: No slide open switch signal failure (Current)
    		-
    Close Switch Failure (Current)
    		Slide close switch failure signal (Current) / ON or OFF
    		ON: Slide close switch signal failure (Current)
    OFF: No slide close switch signal failure (Current)
    		-
    Up Switch Failure (Current)
    		Tilt up switch failure signal (Current) / ON or OFF
    		ON: Tilt up switch signal failure (Current)
    OFF: No tilt up switch signal failure (Current)
    		-
    Down Switch Failure (Current)
    		Tilt down switch failure signal (Current) / ON or OFF
    		ON: Tilt down switch signal failure (Current)
    OFF: No tilt down switch signal failure (Current)
    		-
    Number of Trouble Codes
    		Number of trouble codes / Min.: 0, Max.: 255
    		Number of DTCs displayed
    		-


PERFORM ACTIVE TEST
HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Sliding Roof / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Sliding Roof
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Slide Roof
    		Operate sliding roof
    		Opn/Dwn: Sliding roof slide open or tilt down operation occurs
    Clos/Up: Sliding roof slide close or tilt up operation occurs
    OFF: Sliding roof is not operating
    		-