Audio And Visual System (For Radio And Display Type) Illumination Circuit

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK ILLUMINATION

CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BATTERY)

INSPECT STEERING PAD SWITCH ASSEMBLY

INSPECT SPIRAL CABLE SUB-ASSEMBLY

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - SPIRAL CABLE)

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - BATTERY AND BODY GROUND)

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CAUTION:

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (Toyota Fortuner RM000000KT10ELX.html).

1. Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, glove box or other parts (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.
   

   Result

   Result	Proceed to
   Illumination comes on for all components except steering pad switch assembly.	A
   Illumination comes on for all components except radio and display receiver assembly.	B
   No illumination comes on (radio and display receiver assembly, hazard switch, glove box, etc.).	C

1. Disconnect the S30 spiral cable sub-assembly connector.
   

2. Measure the voltage according to the value(s) in the table below.
   

   Standard Voltage:

   Tester Connection	Switch Condition	Specified Condition
   S30-12 (IL+2) - Body ground	Light control switch TAIL or HEAD	11 to 14 V

   Text in Illustration

   *a	Front view of wire harness connector (to Spiral Cable Sub-assembly)

1. Remove the steering pad switch assembly (Toyota Fortuner RM0000033RT068X.html).
   

   
   
   
   
   

   Text in Illustration

   *A

   w/ Multi-information Display

   -

   -

2. Connect the positive (+) lead of the battery to terminal 5 (IL+2) and the negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.
   

3. Check if the illumination for the steering pad switch assembly comes on.
   

   OK:

   Illumination for the steering pad switch assembly comes on.
   

1. Remove the spiral cable sub-assembly (Toyota Fortuner RM0000010B2003X.html).
   

2. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Condition	Specified Condition
   8 (EAU) - 4 (EAU)	Spiral cable is turned 2.5 rotations counterclockwise	Below 1 Ω
   	Spiral cable is centered
   	Spiral cable is turned 2.5 rotations clockwise
   5 (IL+2) - 12 (IL+2)	Spiral cable is turned 2.5 rotations counterclockwise
   	Spiral cable is centered
   	Spiral cable is turned 2.5 rotations clockwise

   Text in Illustration

   *a	Steering Pad Switch Side
   *b	Vehicle Side

   CAUTION:

   The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (Toyota Fortuner RM000000KT10ELX.html).

1. Disconnect the R19 radio and display receiver assembly connector.
   

2. Disconnect the S30 spiral cable sub-assembly connector.
   

3. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Condition	Specified Condition
   R19-23 (SWG) - S30-4 (EAU)	Always	Below 1 Ω
   R19-23 (SWG) - Body ground	Always	10 kΩ or higher

1. Disconnect the R25 radio and display receiver assembly connector.
   

2. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Condition	Specified Condition
   R25-7 (GND) - Body ground	Always	Below 1 Ω

3. Measure the voltage according to the value(s) in the table below.
   

   Standard Voltage:

   Tester Connection	Switch Condition	Specified Condition
   R25-10 (ILL+) - Body ground	Light control switch TAIL or HEAD	11 to 14 V