Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - DOOR / HATCH
POWER BACK DOOR DRIVE UNIT - INSTALLATION
| 1. INSTALL POWER BACK DOOR UNIT ASSEMBLY |
Attach the 2 claws to install the power back door unit assembly.
Install the 4 bolts.
- Torque:
- 14 N*m{ 143 kgf*cm, 10 ft.*lbf}
Connect the connector.
| 2. INSTALL REAR UPPER PILLAR GARNISH RH |
w/o Power Back Door:
Attach the 5 clips to install the rear upper pillar garnish.
w/ Power Back Door:
Pass the power back door rod through the rear upper pillar garnish.
Attach the 5 clips to install the rear upper pillar garnish.
Install the seat belt shoulder anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to close the seat belt shoulder anchor cover.
| 3. INSTALL BACK DOOR SERVICE HOLE COVER RH |
Install the back door stay plate.
Pass the power back door rod through the hole of the back door service hole cover RH and install the rod with the bolt.
- Torque:
- :
- 18 N*m{ 184 kgf*cm, 13 ft.*lbf}
Move the back door to a half-open position so that the hole in the center of the back door service hole cover RH is aligned lengthwise with the power back door rod.
Attach the 2 clips and install the back door service hole cover RH.
- NOTICE:
- If the back door is in a fully-open position, the power back door rod will interfere with the hole of the back door service hole cover, so do not perform this operation with the back door in a fully open position.
| 4. INSTALL BACK DOOR SIDE GARNISH RH |
w/o Power Back Door:
- HINT:
- Use the same procedure described for the LH side.
w/ Power Back Door:
Attach the clip and 4 claws to install the back door side garnish RH.
| 5. INSTALL CENTER BACK DOOR GARNISH |
Attach the 5 clips and 4 claws to install the center back door garnish.
| 6. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH |
- HINT:
- When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
w/o Rear Air Conditioning System:
Connect the rear seat lock control lever cable.
w/ Rear Air Conditioning System:
Connect the thermistor connector and rear seat lock control lever cable.
Attach the 16 clips and 2 claws to install the quarter trim panel.
Install the clip and bolt.
- Torque:
- 12 N*m{ 122 kgf*cm, 9 ft.*lbf}
w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Attach the 16 clips and 2 claws to install the quarter trim panel.
Install the clip.
w/ Tonneau Cover:
Attach the 16 clips and 2 claws to install the quarter trim panel.
Install the screw and clip.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Install the rear No. 2 seat belt anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
Attach the 3 claws to install the cover.
Install the rear No. 1 seat belt anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
Attach the 3 claws to install the cover.
| 7. INSTALL REAR SEAT COVER CAP RH (w/ Rear No. 2 Seat) |
- HINT:
- Use the same procedure to install the rear seat cover cap on the other side.
Attach the 3 claws to install the rear seat cover cap.
| 8. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE |
Attach the 6 clips to install the support plate.
| 9. INSTALL REAR DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 10. INSTALL REAR STEP COVER |
- HINT:
- Use the same procedure to install the step cover on the other side.
Attach the 2 claws to install the step cover.
| 11. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat) |
()
- HINT:
- Use the same procedure described for the LH side.
| 12. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Install the tonneau cover assembly.
| 13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().