Dtc C1427 Motor Malfunction

Brake. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
Brake Control. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MOTOR RELAY)

INSPECT SKID CONTROL ECU (GND2 TERMINAL)

RECONFIRM DTC

DTC C1427 Motor Malfunction


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
C1427
Actuator pump motor does not operate properly.
  1. Brake actuator assembly (Ground circuit)
  2. Brake actuator assembly (Motor circuit)

WIRING DIAGRAM

Refer to DTCs C0273, C0274 and C1361 (RAV4_ACA30 RM000001JD6075X_02.html).

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (RAV4_ACA30 RM000001K1O00SX.html).
1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MOTOR RELAY)

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select the Active Test mode on the intelligent tester (RAV4_ACA30 RM000000ONK01EX.html).

    ABS/VSC/TRC:
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Motor Relay
    		Motor relay
    		Relay ON / OFF
    		Operating sound of motor can be heard.

  1. Check for operating sound of the motor relay when operating it with the intelligent tester.

    Result:
    Result
    		Proceed to
    Operating sound is not heard.
    		A
    Operating sound is heard.
    		B


B
Go to step 3
A


2.INSPECT SKID CONTROL ECU (GND2 TERMINAL)


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Brake Control.Anti-Lock Brake System. Dtc C1427 Motor Malfunction

  1. Turn the ignition switch off.

  1. Make sure that there is no looseness in the locking part and connecting part of the connectors.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    A67-13 (GND2) - Body ground
    		Always
    		Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)
OK


3.RECONFIRM DTC
HINT:
This code is stored when a problem is identified in the brake actuator assembly.
The motor relay is in the brake actuator assembly.
Therefore, motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.

  1. Turn the ignition switch off.

  1. Reconnect the skid control ECU connector.

  1. Clear the DTCs (RAV4_ACA30 RM000000ONJ02VX.html).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

  1. Check if the same DTC is output (RAV4_ACA30 RM000000ONJ02VX.html).

    Result:
    Result
    		Proceed to
    DTC (C1427) is not output.
    		A
    DTC (C1427) is output.
    		B
    HINT:
    1. If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
    2. If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
    3. If any DTCs are output while jiggling a connector or wire harness of the brake actuator assembly (skid control ECU), inspect and repair the connector or wire harness.
    4. It is suspected that the DTCs were output due to a bad connection of the connector terminal.


B
REPLACE BRAKE ACTUATOR ASSEMBLY (RAV4_ACA30 RM000001XV200PX.html)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (RAV4_ACA30 RM00000135201PX.html)