Power Window Control System Rear Power Window Rh Does Not Operate With Rear Power Window Switch Rh

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING GTS (MAIN BODY)

READ VALUE USING GTS (RR-DOOR MOTOR)

PERFORM ACTIVE TEST USING GTS (RR-DOOR MOTOR)

INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

DESCRIPTION

1. When the ignition switch is ON, the rear power window regulator motor assembly RH is operated by the rear power window regulator switch assembly (for Rear RH Door). The rear power window regulator motor assembly RH has motor, regulator and ECU functions.
   

WIRING DIAGRAM

INSPECTION PROCEDURE

NOTICE:

1. The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (LandCruiser RM000000PY206VX.html).
   
2. If the rear power window regulator motor assembly RH has been replaced with a new one, initialize the power window control system (LandCruiser RM0000011V20BLX.html).
   
3. Check that the window lock switch is off before performing the following procedure.
   
4. Inspect the fuses for circuits related to this system before performing the following procedure.
   

1. Read the Data List according to the display on the GTS (LandCruiser RM0000027QL04NX.html).
   
   

   Main Body

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Communication RRDoor Motor	Connection status between rear power window regulator motor assembly RH and main body ECU (multiplex network body ECU) / STOP or OK	STOP: Communication stopped OK: Normal communication	-

   OK:

   On the GTS screen, OK is displayed.
   

1. Read the Data List according to the display on the GTS (LandCruiser RM0000027QL04NX.html).
   
   

   RR-Door Motor

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   RR Door P/W Up SW	Rear RH door power window manual up switch signal / OFF or ON	OFF: Rear RH door power window manual up switch not being operated ON: Rear RH door power window manual up switch being operated	-
   RR Door P/W Down SW	Rear RH door power window manual down switch signal / OFF or ON	OFF: Rear RH door power window manual down switch not being operated ON: Rear RH door power window manual down switch being operated	-

   OK:

   On the GTS screen, ON or OFF is displayed accordingly.
   

1. Perform the Active Test according to the display on the GTS (LandCruiser RM0000027QL04NX.html).
   

   CAUTION:

   Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

   
   

   RR-Door Motor

   Tester Display	Test Part	Control Range	Diagnostic Note
   Power Window	Power window	OFF/UP/DOWN	-

   HINT:

   Up and down movement does not occur if the arrow is not pressed and held.

   OK:

   Rear RH power window operates normally.
   

1. Remove the rear power window regulator switch assembly RH (LandCruiser RM000002STU0ATX.html).
   

2. Inspect the rear power window regulator switch assembly RH (LandCruiser RM000002R1K05GX.html).
   

1. Disconnect the L2 rear power window regulator switch assembly RH connector.
   

2. Disconnect the L4 rear power window regulator motor assembly RH connector.
   

3. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Condition	Specified Condition
   L2-6 (UP) - L4-10 (UP)	Always	Below 1 Ω
   L2-7 (DOWN) - L4-7 (DOWN)	Always	Below 1 Ω
   L2-6 (UP) - Body ground	Always	10 kΩ or higher
   L2-7 (DOWN) - Body ground	Always	10 kΩ or higher