Впускной Коллектор Установка

Двигатель Гибридная Система Land Cruiser Prado.
Системы Впуска И Выпуска Отработавших Газов Двигателя 5L-E.

  1. INSTALL INTAKE MANIFOLD

  2. INSTALL INJECTION PIPE

  3. INSTALL DIESEL THROTTLE BODY ASSEMBLY

  4. INSTALL INTAKE FLANGE

  5. INSTALL INTAKE PIPE

  6. BLEED INJECTION PIPE

  7. INSPECT FOR FUEL LEAK

Впускной Коллектор -- Установка



1. INSTALL INTAKE MANIFOLD


    .Системы Впуска И Выпуска Отработавших Газов Двигателя 5L-E.Система Впуска Двигателя.Впускной Коллектор Установка

  1. Install a new gasket to the cylinder head with the protrusion facing upward.

    Text in Illustration
    *a
    		Protrusion
    *b
    		Upward


    .Системы Впуска И Выпуска Отработавших Газов Двигателя 5L-E.Система Впуска Двигателя.Впускной Коллектор Установка

  1. Install the intake manifold with the 6 bolts and 2 nuts. Uniformly tighten the bolts and nuts in several steps.

    Момент затяжки:
    24 N*m{240 kgf*cm, 17 ft.*lbf}
    Text in Illustration
    *1
    		Nut

  1. Install the wire harness bracket with the bolt.

    Момент затяжки:
    13 N*m{131 kgf*cm, 9 ft.*lbf}


2. INSTALL INJECTION PIPE

  1. Install the 2 lower clamps to the intake manifold.




  1. Using a 17 mm union nut wrench, install the 4 injection pipes.

    Момент затяжки:
    25 N*m{250 kgf*cm, 18 ft.*lbf}
    ПРИМЕЧАНИЕ:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page Нажмите здесь).

  1. Secure the injection pipes by installing the 2 upper pipe clamps and 2 nuts.

    Момент затяжки:
    5.0 N*m{51 kgf*cm, 44 in.*lbf}


3. INSTALL DIESEL THROTTLE BODY ASSEMBLY

  1. Install a new gasket and the diesel throttle body.

  1. Connect the throttle control motor connector.

  1. Install the bracket with the 2 bolts.

    Момент затяжки:
    13 N*m{131 kgf*cm, 9 ft.*lbf}

  1. Connect the throttle open switch connector.



4. INSTALL INTAKE FLANGE

  1. Install a new gasket and the intake flange with the 3 nuts.

    Момент затяжки:
    12 N*m{122 kgf*cm, 9 ft.*lbf}

  1. Connect the manifold absolute pressure sensor connector.

  1. Install the heater hose bracket with the bolt.

    Момент затяжки:
    14 N*m{138 kgf*cm, 10 ft.*lbf}

  1. Connect the PCV hose.



5. INSTALL INTAKE PIPE

  1. Install the intake pipe with the 2 bolts.

    Момент затяжки:
    18 N*m{184 kgf*cm, 13 ft.*lbf}

  1. Tighten the intake pipe clamp.

    Момент затяжки:
    6.0 N*m{61 kgf*cm, 53 in.*lbf}


6. BLEED INJECTION PIPE

  1. Install the 2 lower clamps to the intake manifold.



    .Системы Впуска И Выпуска Отработавших Газов Двигателя 5L-E.Система Впуска Двигателя.Впускной Коллектор Установка

  1. Install the 4 injection pipes.

    Момент затяжки:
    25 N*m{250 kgf*cm, 18 ft.*lbf}
    Text in Illustration
    *a
    		for Injection Nozzle Side
    *b
    		for Injection Pump Side
    ПРИМЕЧАНИЕ:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page Нажмите здесь).

  1. Install the 2 upper pipe clamps with the 2 nuts.

    Момент затяжки:
    5.0 N*m{51 kgf*cm, 44 in.*lbf}


7. INSPECT FOR FUEL LEAK

  1. Check that there are no fuel leaks anywhere in the fuel system after performing maintenance.

    УКАЗАНИЕ:
    When checking for fuel leaks, make sure that there is pressure in the fuel line.