INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

INSTALL TRANSFER ASSEMBLY

INSTALL MANUAL TRANSMISSION WITH TRANSFER (for 1GR-FE)

INSTALL MANUAL TRANSMISSION WITH TRANSFER (for 1VD-FTV)

INSTALL OIL PAN COVER (for 1VD-FTV)

INSTALL CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE

INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY

INSTALL CLUTCH ACCUMULATOR ASSEMBLY

INSTALL CLUTCH RELEASE CYLINDER TO ACCUMULATOR TUBE

INSTALL NO. 1 CLUTCH HOUSING COVER

CONNECT WIRE HARNESS (for 1GR-FE)

CONNECT WIRE HARNESS (for 1VD-FTV)

INSTALL TRANSFER BREATHER HOSE SUB-ASSEMBLY (for 1GR-FE)

INSTALL TRANSFER BREATHER HOSE SUB-ASSEMBLY (for 1VD-FTV)

INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

INSTALL STARTER ASSEMBLY (for 1GR-FE)

INSTALL NO. 2 MANIFOLD STAY (for 1GR-FE)

INSTALL MANIFOLD STAY (for 1GR-FE)

INSTALL EXHAUST PIPE (for 1GR-FE)

INSTALL EXHAUST PIPE (for 1VD-FTV)

INSTALL FRONT PROPELLER SHAFT ASSEMBLY

INSTALL PROPELLER SHAFT ASSEMBLY

ADD MANUAL TRANSMISSION OIL

INSPECT TRANSMISSION OIL

INSTALL LOWER TRANSFER CASE PROTECTOR

INSTALL TRANSFER DYNAMIC DAMPER (for 1VD-FTV)

INSTALL TRANSFER HEAT INSULATOR

INSTALL TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for 1VD-FTV)

INSTALL AIR TUBE SUB-ASSEMBLY LH (for 1VD-FTV)

INSTALL CLUTCH HOSE (for 1VD-FTV)

INSTALL NO. 2 COOL AIR INLET (w/o Intercooler)

INSTALL INTERCOOLER ASSEMBLY (w/ Intercooler)

INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

INSTALL FLOOR SHIFT LEVER ASSEMBLY

INSTALL SHIFT LEVER BOOT ASSEMBLY

INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

FILL RESERVOIR WITH BRAKE FLUID

BLEED CLUTCH LINE

CHECK FLUID LEVEL IN RESERVOIR

INSPECT FOR CLUTCH FLUID LEAK

CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Apply release hub grease to the release fork, release bearing, push rod contact point and pivot points shown in the illustration.

• Grease:
• Toyota Genuine Release Hub Grease or equivalent

Apply clutch spline grease to the input shaft spline.

• Grease:
• Toyota Genuine Clutch Spline Grease or equivalent

Install the release bearing to the clutch release fork with the clip.

Install the release fork support to the transmission unit.

• Torque:
• 47 N*m{ 480 kgf*cm, 35 ft.*lbf}

Install the clutch release fork with the clutch release bearing to the transmission unit.

• HINT:

• After installation, move the fork back and forth to check that the release bearing slides smoothly.

Install the transfer with the 8 bolts.

• Torque:
• 40 N*m{ 408 kgf*cm, 30 ft.*lbf}

• NOTICE:

• Take care not to damage the adaptor oil seal with the transfer input shaft spline.

Install the manual transmission with transfer with the 9 bolts.

• Torque:
• for bolt A:
• 72 N*m{ 730 kgf*cm, 53 ft.*lbf}
• for bolt B:
• 37 N*m{ 380 kgf*cm, 28 ft.*lbf}

• Bolt Length:

• Item	Length
  Bolt A	50 mm (1.97 in.)
  Bolt B	45 mm (1.77 in.)

Install the manual transmission with transfer with the 10 bolts.

• Torque:
• for bolt A and B:
• 72 N*m{ 730 kgf*cm, 53 ft.*lbf}
• for bolt C:
• 39 N*m{ 400 kgf*cm, 29 ft.*lbf}

• Bolt Length:

• Item	Length
  Bolt A	45 mm (1.77 in.)
  Bolt B	50 mm (1.97 in.)
  Bolt C	70 mm (2.76 in.)

Install the oil pan cover with the 2 bolts.

• Torque:
• 21 N*m{ 214 kgf*cm, 15 ft.*lbf}

Install the flexible hose tube with the 3 bolts.

• Torque:
• 20 N*m{ 204 kgf*cm, 15 ft.*lbf}

Install the clutch release cylinder with the 2 bolts.

• Torque:
• 12 N*m{ 120 kgf*cm, 9 ft.*lbf}

Install the clutch accumulator with the 3 bolts.

• Torque:
• 12 N*m{ 120 kgf*cm, 9 ft.*lbf}

Using a union nut wrench, connect the flexible hose tube.

• Torque:
• 15 N*m{ 155 kgf*cm, 11 ft.*lbf}

• NOTICE:

• Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench ().

Using a union nut wrench, connect the tube to the clutch accumulator and release cylinder.

• Torque:
• 16 N*m{ 158 kgf*cm, 11 ft.*lbf}

• NOTICE:

• Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench ().

Install the tube with the 2 bolts.

• Torque:
• 12 N*m{ 120 kgf*cm, 9 ft.*lbf}

Install the housing cover with the 3 bolts.

• Torque:
• 12 N*m{ 120 kgf*cm, 9 ft.*lbf}

Connect the 6 clamps.

Connect the back-up light switch connector.

Install the 2 bolts.

• Torque:
• for LH side:
• 29 N*m{ 296 kgf*cm, 21 ft.*lbf}
• for RH side:
• 60 N*m{ 612 kgf*cm, 44 ft.*lbf}

Connect the ground cable with the bolt.

• Torque:
• 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Connect the 2 connectors and 3 clamps.

Connect the 5 clamps.

Connect the back-up light switch connector.

Connect the shift position switch connector.

Connect the ground cable with the bolt.

• Torque:
• 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Connect the 2 connectors and 3 clamps.

Connect the 2 breather hoses to the bracket.

Connect the 5 clamps.

Connect the breather hose to the transfer and actuator, and attach the 2 clamps.

Install the bracket with the bolt.

Connect the 3 breather hoses to the bracket.

Connect the 3 clamps.

Connect the breather hose to the transfer and actuator, and attach the 2 clamps.

Install the engine mounting insulator to the transmission with the 4 bolts.

• Torque:
• 59 N*m{ 602 kgf*cm, 44 ft.*lbf}

Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.

• Torque:
• 37 N*m{ 377 kgf*cm, 27 ft.*lbf}

Install the frame crossmember to the vehicle body with the 4 bolts, 4 washers and 4 nuts.

• Torque:
• 110 N*m{ 1,122 kgf*cm, 81 ft.*lbf}

Install the No. 2 manifold stay with the 3 bolts.

• Torque:
• 40 N*m{ 408 kgf*cm, 30 ft.*lbf}

Install the manifold stay with the 3 bolts.

• Torque:
• 40 N*m{ 408 kgf*cm, 30 ft.*lbf}

Park the vehicle in a level place.

Check that the oil level is within 5 mm (0.196 in.) of the lowest point of the transmission filler plug opening.

• NOTICE:

Inspect for oil leaks when the oil level is low.

Install a new gasket and the filler plug.

• Torque:
• 37 N*m{ 380 kgf*cm, 27 ft.*lbf}

Install the lower transfer case protector with the 7 bolts.

• Torque:
• 14 N*m{ 139 kgf*cm, 10 ft.*lbf}

Install the transfer dynamic damper with the 2 bolts.

• Torque:
• 12 N*m{ 122 kgf*cm, 9 ft.*lbf}

Install the insulator with the 4 bolts.

• Torque:
• 30 N*m{ 306 kgf*cm, 22 ft.*lbf}

Temporarily install the flare nut of the tube connector to flexible hose tube to the clutch tube to release cylinder 2 way by hand.

Temporarily install the tube connector to flexible hose tube with the 2 bolts.

Tighten the bolt labeled A.

• Torque:
• 20 N*m{ 204 kgf*cm, 15 ft.*lbf}

• NOTICE:

• Tighten the bolt labeled B after installing the clutch hose.

Install the air tube to the throttle body.

Align the embossed mark of the throttle body with the paint mark of the No. 4 air hose.

Tighten the hose clamp so that it is 7 to 11 mm (0.276 to 0.433 in.) from the end of the hose as shown in the illustration.

• Torque:
• 6.3 N*m{ 64 kgf*cm, 56 in.*lbf}

Connect the clutch hose to the air tube with the bolt labeled A.

Temporarily install the clutch hose to the clutch master cylinder tube to flexible hose tube and tube connector to flexible hose tube, and fix it in place with the 2 clips.

• Torque:
• 20 N*m{ 204 kgf*cm, 15 ft.*lbf}

Tighten the bolt labeled B.

• Torque:
• 20 N*m{ 204 kgf*cm, 15 ft.*lbf}

Tighten the flexible hose tube.

• NOTICE:

• HINT:

Using a 10 mm union nut wrench, tighten the 2 flare nuts of the flexible hose tube.

• Torque:
• without union nut wrench:
• 15 N*m{ 154 kgf*cm, 11 ft.*lbf}
• with union nut wrench:
• 14 N*m{ 141 kgf*cm, 10 ft.*lbf}

Using a 10 mm union nut wrench, tighten the flare nut of the flexible hose tube.

• Torque:
• without union nut wrench:
• 15 N*m{ 154 kgf*cm, 11 ft.*lbf}
• with union nut wrench:
• 14 N*m{ 141 kgf*cm, 10 ft.*lbf}

Install a new gasket to the air tube LH.

• HINT:

• Install the gasket with the protrusion facing as shown in the illustration.

Install the No. 2 cool air inlet with the 3 nuts and bolt.

• Torque:
• 21 N*m{ 214 kgf*cm, 15 ft.*lbf}

Connect the No. 2 air hose to the No. 2 cool air inlet.

Tighten the No. 2 air hose clamp.

• Torque:
• 6.3 N*m{ 64 kgf*cm, 56 in.*lbf}

• HINT:

()

Install the engine cover with the 2 nuts.

• Torque:
• 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Apply MP grease to the tip of the shift lever.

Cover the shift lever cap with a cloth.

Press down on the shift lever cap and rotate it clockwise to install it.

Install the shift lever retainer and shift lever boot with the 4 screws.

Fill the reservoir with brake fluid.

• Brake Fluid:
• SAE J1703 or FMVSS No. 116 DOT 3

Remove the release cylinder bleeder plug cap.

Connect a vinyl tube to the bleeder plug.

Depress the clutch pedal several times, and then loosen the bleeder plug while the pedal is depressed.

When fluid no longer comes out, tighten the bleeder plug, and then release the clutch pedal.

Repeat the previous 2 steps until all the air in the fluid is completely bled.

Tighten the bleeder plug.

• Torque:
• 11 N*m{ 110 kgf*cm, 8 ft.*lbf}

Install the bleeder plug cap.

Check that all the air has been bled from the clutch line.

Check the fluid level.

If the brake fluid level is low, check for leaks and inspect the disc brake pad. If necessary, refill the reservoir with brake fluid after repair or replacement.

• Brake fluid:
• SAE J1703 or FMVSS No. 116 DOT 3