Vehicle Stability Control System (W/O Vdim) Tc And Cg Terminal Circuit

Brake. Lexus Is250, Is220D. Gse20 Ale20
Brake Control. Lexus Is250, Is220D. Gse20 Ale20

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK CAN COMMUNICATION SYSTEM

INSPECT DLC3

CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)

CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

CHECK ECM (TC of DLC3 INPUT)

VEHICLE STABILITY CONTROL SYSTEM (w/o VDIM) - TC and CG Terminal Circuit


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light.

WIRING DIAGRAM


Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).Vehicle Stability Control System (W/O Vdim)  Tc And Cg Terminal Circuit


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).
1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if the CAN communication system DTC is output (Click here for LHD, or Click here for RHD).

    Result:

    Condition
    Proceed to
    DTC is not output
    A
    DTC is output
    B


B
INSPECT CAN COMMUNICATION SYSTEM
A


2.INSPECT DLC3


    Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).Vehicle Stability Control System (W/O Vdim)  Tc And Cg Terminal Circuit
  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    J21-13 (TC) - J21-4 (CG)
    Engine switch on (IG)
    10 to 14 V


OK
Go to step 5
NG


3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)


    Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).Vehicle Stability Control System (W/O Vdim)  Tc And Cg Terminal Circuit
  1. Turn the engine switch off.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J21-13 (TC) - A6-3 (TC)
    Always
    Below 1 Ω
    J21-13 (TC) - Body ground
    Always
    10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)


    Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).Vehicle Stability Control System (W/O Vdim)  Tc And Cg Terminal Circuit
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J21-4 (CG) - Body ground
    Always
    Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK ECM (TC of DLC3 INPUT)


    Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).Vehicle Stability Control System (W/O Vdim)  Tc And Cg Terminal Circuit
  1. Reconnect the ECM connector.

  1. Using SST, connect terminals TC and CG of the DLC3.

  1. Turn the engine switch on (IG).

  1. Check that the engine warning light is blinking.

    Result:

    Condition
    Proceed to
    Engine warning light is blinking
    A
    Engine warning light is not blinking
    B
    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).


B
REPAIR OR REPLACE WIRE HARNESS OR ECM (TC of ECM CIRCUIT)
A

REPLACE BRAKE ACTUATOR ASSEMBLY