Oil Level Sensor - Installation

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - 3UR-FE LUBRICATION

OIL LEVEL SENSOR - INSTALLATION

1. INSTALL ENGINE OIL LEVEL SENSOR

Install a new gasket and the oil level sensor with the 4 bolts.

  • Torque:
  • 7.0 N*m{ 71 kgf*cm, 62 in.*lbf}

Connect the oil level sensor connector.

2. CONNECT OIL COOLER PIPE ASSEMBLY

Connect the oil cooler pipe with the 2 bolts.

  • Torque:
  • 14 N*m{ 143 kgf*cm, 10 ft.*lbf}
3. ADD ENGINE OIL

Add fresh oil and install the oil filler cap.

  • Standard Oil Grade:
  • Oil GradeOil Viscosity (SAE)
    API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil5W-30
    10W-30
    API grade SL, SM or SN multigrade engine oil15W-40
    20W-50
  • Standard Oil Capacity:
  • ItemSpecified Condition
    Drain and refill without oil filter change7.1 liters (7.5 US qts, 6.2 Imp. qts)
    Drain and refill with oil filter change7.5 liters (7.9 US qts, 6.6 Imp. qts)
    Dry fill9.3 liters (9.8 US qts, 8.2 Imp. qts)
4. INSPECT FOR OIL LEAK

Start the engine. Make sure that there are no oil leaks from the area that was worked on.

5. INSPECT ENGINE OIL LEVEL

Warm up the engine. Then stop the engine and wait for 5 minutes.

Oil Level Sensor - Installation. 3UR-FE LUBRICATION. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Check that the engine oil level is between the dipstick low level mark and full level mark.

Text in Illustration
*aMeasuring Surface
*bLow Level Mark
*cFull Level Mark

If the level is low, check for leakage and add oil up to the full level mark.

  • NOTICE:
  • Do not fill engine oil above the full level mark.
  • HINT:
  • A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
If low quality oil or oil of an inappropriate viscosity is used.
When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.
When leaving the idling for a long time, or when driving frequently through heavy traffic.
  • When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.
6. INSTALL NO. 2 ENGINE UNDER COVER

Install the No. 2 engine under cover with the 2 bolts.

  • Torque:
  • 29 N*m{ 296 kgf*cm, 21 ft.*lbf}
7. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Install the No. 1 engine under cover with the 10 bolts.

  • Torque:
  • 29 N*m{ 296 kgf*cm, 21 ft.*lbf}
8. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Push in the clip to install the front fender splash shield sub-assembly LH.

Install the 3 bolts and screw.

9. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Push in the clip to install the front fender splash shield sub-assembly RH.

Install the 3 bolts and 2 screws.