Dtc B2286 Runnable Signal Malfunction

Engine. Lexus Is250, Is220D. Gse20 Ale20
4Gr-Fse Starting. Lexus Is250, Is220D. Gse20 Ale20

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK OPERATION OF TACHOMETER

CHECK DTC OUTPUT (MULTIPLEX NETWORK COMMUNICATION SYSTEM (BEAN))

CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)

CHECK CONNECTORS

CHECK WIRE HARNESS (POWER SOURCE CONTROL ECU - BODY GROUND)

CHECK WIRE HARNESS (POWER SOURCE CONTROL ECU - ECM)

READ VALUE OF INTELLIGENT TESTER

RECHECK FOR DTC

DTC B2286 Runnable Signal Malfunction


DESCRIPTION

This DTC is output when serial communication signals and multiplex communication signals in the circuit between the power source control ECU and ECM are inconsistent.
HINT:
When the power source control ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.

DTC No.
DTC Detection Condition
Trouble Area
B2286
Serial communication signals and multiplex communication signals in the circuit between the power source control ECU and engine control ECU are inconsistent.
  1. Multiplex communication system
  2. CAN communication system
  3. ECM
  4. Power source control ECU
  5. Wire harness or connector

WIRING DIAGRAM


Lexus Is250, Is220D. Gse20 Ale20.4Gr-Fse Starting.Starting System. Dtc B2286 Runnable Signal Malfunction


INSPECTION PROCEDURE

1.CHECK OPERATION OF TACHOMETER

  1. Run the engine and check if the function of the tachometer in the combination meter is normal.

    OK:
    Actual engine revolution speed and the revolution indicated on the tachometer are the same.


NG
GO TO COMBINATION METER SYSTEM
OK


2.CHECK DTC OUTPUT (MULTIPLEX NETWORK COMMUNICATION SYSTEM (BEAN))

  1. Delete the DTC (Click here).

  1. Check for the multiplex network communication system DTCs B1210, B1214 and B1215.

    HINT:
    If the DTCs for the multiplex network communication system malfunction are output, inspect those DTCs first (Click here).
    OK:
    No DTC is output.


NG
GO TO MULTIPLEX COMMUNICATION SYSTEM
OK


3.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)

  1. Delete the DTC (Click here).

  1. Check for the CAN communication system DTC U0146.

    HINT:
    If the DTCs for the CAN communication system malfunction are output, inspect those DTCs first (LHD: Click here, RHD: Click here).
    OK:
    No DTC is output.


NG
GO TO CAN COMMUNICATION SYSTEM
OK


4.CHECK CONNECTORS

  1. Check that the connectors are securely connected and the terminals are not deformed or loose.

    OK:
    The connectors are securely connected and the terminals are not deformed or loose.


NG
REPAIR OR REPLACE CONNECTORS
OK


5.CHECK WIRE HARNESS (POWER SOURCE CONTROL ECU - BODY GROUND)


    Lexus Is250, Is220D. Gse20 Ale20.4Gr-Fse Starting.Starting System. Dtc B2286 Runnable Signal Malfunction

  1. Disconnect the ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection (Symbols)
    		Condition
    		Specified Condition
    J55-6 (GND2) - Body ground
    		Always
    		Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK WIRE HARNESS (POWER SOURCE CONTROL ECU - ECM)


    Lexus Is250, Is220D. Gse20 Ale20.4Gr-Fse Starting.Starting System. Dtc B2286 Runnable Signal Malfunction

  1. Disconnect the A6 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection (Symbols)
    		Condition
    		Specified Condition
    J55-2 (TACH) - A6-16 (TACH)
    		Always
    		Below 1 Ω
    J55-2 (TACH) or A6-16 (TACH) - Body ground
    		Always
    		10 kΩ or higher
    HINT:
    If the result of the inspection for a short circuit is not as specified, there may be a short in the ECU.


NG
REPAIR OR REPLACE HARNESS, CONNECTOR OR EACH ECU
OK


7.READ VALUE OF INTELLIGENT TESTER

  1. Reconnect the connectors.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Check the DATA LIST for proper functioning of the engine running.

    Power Source Control:
    Item
    		Measurement Item/Display (Range)
    		Normal Condition
    		Diagnostic Note
    E/G Cond
    		Engine condition/ STOP or RUN
    		STOP: Engine is stopped
    RUN: Engine is running
    		-
    OK:
    STOP (engine is stopped) and RUN (engine is running) appear on the screen.


NG
REPLACE ECM
OK


8.RECHECK FOR DTC

  1. Delete the DTCs (Click here).

  1. After DTCs are all cleared, turn the engine switch on (IG). After 30 seconds have elapsed, check for DTCs again.

    OK:
    DTC B2286 is not output.


NG
REPLACE POWER SOURCE CONTROL ECU
OK

CHECK INTERMITTENT PROBLEMS