Dtc P0781 1-2 Shift (1-2 Shift Valve)

SYSTEM DESCRIPTION

MONITOR DESCRIPTION

INSPECTION PROCEDURE

CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0781)

PERFORM ACTIVE TEST BY INTELLIGENT TESTER

INSPECT SHIFT SOLENOID VALVE SLT

CLEAR THE DTC AND RUNNING TEST

SYSTEM DESCRIPTION

1. 
   The 1-2 shift valve performs shifting to 1st gear and other gears.
   
   
   

   DTC No.	DTC Detection Condition	Trouble Area
   P0781	1-2 shift valve malfunction: Shifting to 2nd and 4th gears is impossible. When the ECM directs the gearshift to switch to 5th or 6the gear, the engine overruns (clutch slips). (2-trip detection logic) (a) and (b), or (a) and (c) (a) When the ECM directs the gearshift to switch to 2nd gear, the actual gear is shifted to 1st. (b) When the ECM directs the gearshift to switch to 4th gear, the actual gear is shifted to 3rd. (c) When the ECM directs the gearshift to switch to 5th gear, the engine overruns (clutch slips).	Shift solenoid valve SLT remains open or closed Valve body is blocked up or stuck (1-2 shift valve) Automatic transmission (clutch, brake or gear, etc.)

   
   

   HINT:

   1. Gear positions in the event of a solenoid valve mechanical problem:
      
      

      ECM command gearshift	1st	2nd	3rd	4th	5th	6th
      Actual gear position under malfunction	↑	1st	↑	3rd	N*	N*

      N*: Neutral
      
   2. Gear position during fail-safe operation:
      If any malfunction is detected, the ECM changes into the fail-safe mode to shift into the gear positions as shown in the table below.
      
   
   

   Gear position under normal conditions	1st	2nd	3rd	4th	5th	6th
   Actual gear position under fail safe mode	↑ (*1)	1st (*1)	↑	3rd	3rd	3rd

   *1: Under engine braking, downshifting to 1st or 2nd gear is prohibited.

MONITOR DESCRIPTION

INSPECTION PROCEDURE

1. Connect the intelligent tester to the DLC3.
   

2. Turn the engine switch on (IG) position.
   

3. Turn on the tester.
   

4. Select the item "Power train / ECT / DTC / Current or Pending".
   

5. Read the DTCs using the intelligent tester.
   
   

   Result:

   
   

   Display (DTC output)	Proceed to
   Only "P0781" is output	A
   "P0781" and other DTCs	B

   HINT:

   If any other codes besides "P0781" are output, perform troubleshooting for those DTCs first.

HINT:

Performing the intelligent tester Active Test allows relay, Vacuum Switching Valve (VSV), actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to shorten labor time.

The Data List can be displayed during the Active Test.

1. Warm up the engine.
   

2. Turn the engine switch off.
   

3. Connect the intelligent tester to the DLC3.
   

4. Turn the engine switch on (IG) position.
   

5. Turn on the tester.
   

6. Select the item "Enter / Power train / ECT / Active Test ".
   

7. Follow the instructions on the tester and read the Active Test.
   

   HINT:

   While driving, the shift position can be forcibly changed with the intelligent tester.

   Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you to confirm the problem (Click here).

   
   

   Item	Test Details	Diagnostic Note
   Control the Shift Position	[Test Details] Operate the shift solenoid valve and set the each shift position by yourself. [Vehicle Condition] IDL: ON Less than 50 km/h (31 mph) [Others] Press "→" button: Shift up Press "←" button: Shift down	Possible to check the operation of the shift solenoid valves.

   HINT:

   1. This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
      
   2. The 4th to 5th and 5th to 6th up-shiftings must be performed with the accelerator pedal released.
      
   3. The 6th to 5th and 5th to 4th down-shiftings must be performed with the accelerator pedal released.
      
   4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
      
   5. The shift position commanded by the ECM is shown in the DATA LIST (Shift Status) display on the intelligent tester.
      
   6. Gear positions in the event of a solenoid valve mechanical problem:
      
   
   

   Tester command gear shift	1st	2nd	3rd	4th	5th	6th
   Actual gear position under malfunction	↑	1st	↑	3rd	N*	N*

   N*: Neutral
   

   OK:

   Gear position changes in accordance with the tester command.
   

1. Remove the shift solenoid valve SLT.
   

2. Measure the resistance according to the value(s) in the table below.
   

   Resistance:

   Tester Connection	Specified Condition 20°C (68°F)
   1 - 2	5.0 to 5.6 Ω

3. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
   

   OK:

   The solenoid makes an operating sound.
   

1. Clear the DTC, and check DTC again after conducting the "MONITOR DRIVE PATTERN FOR ECT TEST" (Click here).
   

   OK:

   No DTC code