Clutch Drum And Input Shaft Assembly Disassembly

Place the oil pump onto the torque converter clutch, and then place the clutch drum and input shaft onto the oil pump.

Using a screwdriver, remove the snap ring from the clutch drum and input shaft.

Remove the reverse clutch hub sub-assembly with the reverse clutch reaction sleeve, the clutch cushion plate, the reverse clutch flange, the 5 rear clutch discs, and the 4 clutch plates from the forward clutch hub.

Remove the reverse clutch reaction sleeve from the reverse clutch hub sub-assembly.

Remove the clutch cushion plate, the reverse clutch flange, the 4 plates and the 5 discs from the reverse clutch hub.

Check whether the sliding surfaces of the discs, the plates, and the flange are worn or burnt.
If necessary, replace them.

NOTICE:

1. If the linings of the discs are peeled off or discolored, or even a part of the printed numbers is damaged, replace all discs.
   

1. Before assembling new discs, soak them in ATF for at least 15 minutes.
   

Inspect the pack clearance of the reverse clutch hub sub-assembly.

1. Using a dial indicator, measure the reverse clutch piston stroke (distance A) and the moving distance (distance B) of the reverse clutch flange at both ends across the diameter while blowing air (392 kPa, 4 kgf/cm², 57 psi) from the oil hole as shown in the illustration, and calculate the average.
   
   

   
   
   
   

   HINT:

   Piston stroke A = 1.05 to 2.15 mm

   Flange moving distance B = 0.72 to 1.08 mm

   Pack clearance = Piston stroke A - Flange moving distance B - 0.06

   Pack Clearance:

   0.5 to 0.8 mm (0.020 to 0.031 in.)
   

   NOTICE:

   Install a selective flange (t = 3.3 mm) when measuring the moving distance. (shaded area in the illustration)

2. If the pack clearance is outside the standard, select and install a clutch flange that brings the pack clearance within the standard.
   

   HINT:

   There are 11 types of flanges that can be used to adjust the pack clearance. Select the one with the most appropriate thickness.

   Flange thickness:

   No.	Thickness
   0	2.8 mm (0.110 in.)
   1	2.9 mm (0.114 in.)
   2	3.0 mm (0.118 in.)
   3	3.1 mm (0.122 in.)
   4	3.2 mm (0.126 in.)
   5	3.3 mm (0.130 in.)
   6	3.4 mm (0.134 in.)
   7	3.5 mm (0.138 in.)
   8	3.6 mm (0.142 in.)
   9	3.7 mm (0.146 in.)
   A	3.8 mm (0.150 in.)

Remove the forward clutch hub sub-assembly and thrust washer from the clutch drum assembly.

Remove the 2 thrust needle roller bearings and thrust bearing race No.3 from the forward clutch hub sub-assembly.

Using a dial indicator, measure the inside diameter of the forward clutch hub bushing.

Standard inside diameter:

26.037 to 26.062 mm (1.0251 to 1.0261 in.)

Remove the coast clutch hub sub-assembly from the clutch drum sub-assembly.

Hold the coast clutch hub and turn the 1 way clutch assembly.

Check that the 1 way clutch assembly turns freely counterclockwise and locks clockwise.
If there is a problem with the 1 way clutch, replace it.

Remove the underdrive 1 way clutch assembly, clutch hub thrust washer and the thrust bearing race from the coast clutch hub.

Using a screwdriver, remove the hole snap ring.

Remove the flange, cushion plate, 4 discs and 4 plates from the input shaft.

Check whether the sliding surfaces of the discs, the plates, and the flange are worn or burnt.
If necessary, replace them.

NOTICE:

1. If the linings of the discs are peeled off or discolored, or even a part of the printed numbers is damaged, replace all discs.
   

1. Before assembling new discs, soak them in ATF for at least 15 minutes.
   

Using a screwdriver, remove the hole snap ring.

Remove the flange, the 3 discs and the 3 plates from the input shaft.

Check whether the sliding surfaces of the discs, the plates, and the flange are worn or burnt.
If necessary, replace them.

NOTICE:

1. If the linings of the discs are peeled off or discolored, or even a part of the printed numbers is damaged, replace all discs.
   

1. Before assembling new discs, soak them in ATF for at least 15 minutes.
   

Remove the thrust needle roller bearing from the input shaft.

Remove the input shaft from the clutch drum.

Remove the thrust needle roller bearing and thrust bearing race from the clutch drum.

Remove the 4 oil seal rings from the input shaft.

Place SST on the clutch balancer No.1, and compress the return spring with a press.

SST

09350-30020(09350-07040)

Using SST and press, remove the snap ring.

SST

09350-30020(09350-07070)

Remove the clutch balancer No.1 and the forward clutch return spring from the input shaft.

Remove the O-ring from the clutch balancer No.1.

Using vernier calipers, measure the free length of the spring together with the spring seat.

Standard free length:

24.64 mm (0.9701 in.)

Holding the forward clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm², 57 psi) to the input shaft to remove the forward clutch piston.

Remove the coast clutch piston from the forward clutch piston.

Remove the O-ring from the forward clutch piston.

Remove the reverse clutch flange from the clutch drum assembly.

Using a screwdriver, remove the 2 hole snap rings from the clutch drum assembly.

Remove the reverse clutch flange, the 5 plates and the 4 discs from the clutch drum assembly.

Check whether the sliding surfaces of the discs, the plates, and the flange are worn or burnt.
If necessary, replace them.

NOTICE:

1. If the linings of the discs are peeled off or discolored, or even a part of the printed numbers is damaged, replace all discs.
   

1. Before assembling new discs, soak them in ATF for at least 15 minutes.
   

Place SST on the clutch balancer No.3, and compress the return spring with a press.

SST

09387-00070

Using SST and press, remove the snap ring.

SST

09350-30020(09350-07070)

Remove the clutch balancer No.3.

Remove the reverse clutch return spring and the O-ring from the reverse clutch piston.

Using vernier calipers, measure the free length of the spring together with the spring seat.

Standard free length:

21.04 mm (0.828 in.)

Remove the reverse clutch piston sub-assembly from the clutch drum sub-assembly.

Remove the O-ring from the reverse clutch piston sub-assembly.

Remove the O-ring from the clutch drum sub-assembly.

Place SST on the direct clutch piston, and compress the return spring with a press.

SST

09320-89010

Using SST and press, remove the snap ring.

SST

09350-30020(09350-07070)

Using 2 screwdrivers, remove the direct clutch piston sub-assembly from the clutch drum.

Remove the clutch balancer No.2 and the direct clutch return spring sub-assembly from the direct clutch piston sub-assembly.

Remove the 2 O-rings from the direct clutch piston sub-assembly.

Using vernier calipers, measure the free length of the spring together with the spring seat.

Standard free length:

19.51 mm (0.768 in.)