Front Bumper (For Standard) Reassembly

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Exterior Panels Trim. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. INSTALL FRONT NO. 2 BUMPER PROTECTOR

  2. INSTALL FRONT BUMPER GUARD (w/ Garnish)

  3. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ Bracket)

  4. INSTALL LOWER NO. 1 RADIATOR GRILLE

  5. INSTALL FRONT BUMPER HOLE COVER LH (w/ Fog Light)

  6. INSTALL FRONT BUMPER HOLE COVER RH (w/ Fog Light)

  7. INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light)

  8. INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light)

  9. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

  10. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

  11. INSTALL FRONT BUMPER INNER BRACKET (w/ Fog Light)

  12. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

  13. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

  14. INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

  15. INSTALL NO. 4 ENGINE ROOM WIRE

  16. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

  17. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

  18. INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

  19. INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

  20. INSTALL HEADLIGHT CLEANER HOSE

Front Bumper (For Standard) -- Reassembly


HINT:
When installing the front bumper protector, heat the front bumper surface using a heat light.
Standard Heating Temperature:
Item
Temperature
Front Bumper
20 to 30°C (68 to 86°F)
NOTICE:
Do not heat the front bumper excessively.


1. INSTALL FRONT NO. 2 BUMPER PROTECTOR

  1. Clean the front bumper surface.

    1. Using a heat light, heat the front bumper cover surface.

    2. Remove the double-sided tape from the front bumper cover.

    3. Wipe off any tape adhesive residue with cleaner.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Install a new front No. 2 bumper protector.

    1. Remove the peeling paper from the face of 2 new front No. 2 bumper protectors.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    2. Install the 2 front No. 2 bumper protectors as shown in the illustration.



2. INSTALL FRONT BUMPER GUARD (w/ Garnish)

  1. Attach the 6 clips to install the front bumper guard.

  1. Install the 4 nuts.



3. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ Bracket)

  1. Attach the 2 claws.

  1. Install the front bumper extension mounting bracket with the 2 bolts.



4. INSTALL LOWER NO. 1 RADIATOR GRILLE

  1. Attach the 16 claws to install the lower No. 1 radiator grille.

  1. Install the 4 retainers.



5. INSTALL FRONT BUMPER HOLE COVER LH (w/ Fog Light)

  1. Attach the 5 claws to the front bumper hole cover LH.

  1. Install the 2 screws and 2 retainers.



6. INSTALL FRONT BUMPER HOLE COVER RH (w/ Fog Light)
HINT:
Use the same procedure described for the LH side.


7. INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light)

  1. Attach the 5 claws to the front bumper hole cover LH.

  1. Install the screw and 2 retainers.



8. INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light)
HINT:
Use the same procedure described for the LH side.


9. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

  1. Connect the connector.

  1. Attach the 2 guides and install the fog light assembly LH.

  1. Install the 2 screws.



10. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)
HINT:
Use the same procedure described for the LH side.


11. INSTALL FRONT BUMPER INNER BRACKET (w/ Fog Light)

  1. Attach the 3 claws and install the front bumper inner bracket.



12. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
HINT:
Use the same procedure to install the No. 2 ultrasonic sensor retainer on the other side.


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Exterior Panels Trim.Front Bumper (For Standard).Front Bumper (For Standard) Reassembly

  1. Temporarily install the No. 2 ultrasonic sensor retainer to the front bumper.

    Text in Illustration
    *a
    		Protrusion
    *b
    		Keyhole
    NOTICE:
    1. Do not damage the bumper with the protrusion when installing the retainer.
    2. Securely install the No. 2 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the front bumper.


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Attach the 2 claws to install the No. 2 ultra sonic sensor retainer.



13. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
HINT:
Use the same procedure to install the No. 1 ultrasonic sensor on the other side.

  1. Attach the 2 claws to install the ultrasonic sensor.

    NOTICE:
    Push the No. 2 ultrasonic sensor retainer from the outside of the bumper when there is a gap between the retainer and the bumper surface. In this case, do not push on the No. 1 ultrasonic sensor.


14. INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

  1. Attach the 4 claws to install the ultrasonic sensor clip.

    NOTICE:
    Hold the No. 1 ultrasonic sensor in place so that the No. 2 ultrasonic sensor retainer does not come out when installing the ultrasonic sensor clip.


15. INSTALL NO. 4 ENGINE ROOM WIRE

  1. w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Install the No. 4 engine room wire.

    1. Attach the 11 clamps to install the No. 4 engine room wire.

    2. Connect the 2 connectors.

  1. w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Install the No. 4 engine room wire.

    1. Attach the 12 clamps to install the No. 4 engine room wire.

    2. Connect the 4 connectors.

  1. w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Install the No. 4 engine room wire.

    1. Attach the 12 clamps to install the No. 4 engine room wire.

    2. Connect the 2 connectors.



16. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

  1. Attach the 2 claws.

  1. Install the headlight washer actuator sub-assembly LH with the bolt.

    Torque:
    1.1 N*m{11 kgf*cm, 10 in.*lbf}


17. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)
HINT:
Use the same procedure described for the LH side.


18. INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

  1. Attach the 2 claws to install the type 1 headlight washer nozzle sub-assembly LH.



19. INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)
HINT:
Use the same procedure described for the LH side.


20. INSTALL HEADLIGHT CLEANER HOSE

  1. Attach the 4 clamps and install the headlight cleaner hose.

  1. Connect the headlight cleaner hose.