Wiper Ecu -- Removal |
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 3. REMOVE NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION |
for Type A:
Put protective tape around the No. 1 instrument panel finish panel cushion.
Text in Illustration *a Protective Tape Using a moulding remover B, detach the 4 claws and 3 clips and remove the No. 2 instrument panel finish panel cushion.
for Type B:
Put protective tape around the No. 1 instrument panel finish panel cushion.
Text in Illustration *a Protective Tape Using a moulding remover, detach the 7 claws and remove the No. 2 instrument panel finish panel cushion.
| 4. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH |
for Type A:
Put protective tape around the lower instrument panel pad sub-assembly RH.
Text in Illustration *a Protective Tape Remove the clip and screw.
Detach the 11 claws and guide and remove the lower instrument panel pad sub-assembly RH.
for Type B:
Put protective tape around the lower instrument panel pad sub-assembly RH.
Text in Illustration *a Protective Tape Remove the clip and screw.
Detach the 7 claws and remove the lower instrument panel pad sub-assembly RH.
| 5. REMOVE INSTRUMENT SIDE PANEL RH |
 |
Put protective tape around the instrument side panel RH.
Text in Illustration *a Protective Tape
Using a moulding remover A, detach the 6 claws and remove the instrument side panel RH.
w/ Airbag Cut Off Switch:
Disconnect the connector and remove the instrument side panel RH.
| 6. REMOVE FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 7. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover) |
 |
Detach the 4 claws and 3 guides.
Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.
| 8. REMOVE COWL SIDE TRIM BOARD RH |
 |
Remove the cap nut.
Text in Illustration *a Cap Nut
Detach the 2 clips and remove the cowl side trim board LH.
| 9. REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY |
Remove the 4 bolts.
 |
Detach the 4 claws and remove the front passenger side knee airbag assembly.
Using a screwdriver, release the connector lock and disconnect the airbag connector.
Text in Illustration *a Connector Lock 
Protective Tape - NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
- CAUTION:
- Tape the screwdriver tip before use.
| 10. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
 |
Put protective tape around the No. 3 instrument cluster finish panel garnish.
Text in Illustration *a Protective Tape
Using a moulding remover A, detach the 6 claws and remove the No. 3 instrument cluster finish panel garnish.
| 11. REMOVE INSTRUMENT PANEL BOX DOOR KNOB |
- HINT:
- Use the same procedure for both instrument panel box door knobs.
Using a moulding remover B, detach the 2 claws and remove the instrument panel box door knob.
 |
| 12. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL |
 |
Put protective tape around the lower No. 2 instrument panel finish panel.
Remove the 4 screws <C>.
Text in Illustration *a Protective Tape *b Screw <C>
Detach the 3 claws.
 |
Disconnect the connector and remove the lower No. 2 instrument panel finish panel.
| 13. REMOVE WINDSHIELD WIPER RELAY ASSEMBLY |
Disconnect the connector.
 |
Remove the screw.
Detach the 2 guides and remove the windshield wiper relay assembly