Front Wiper Motor Inspection

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200

Wiper Washer. Land Cruiser. Urj200, 202 Grj200 Vdj200

INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)
INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)

Front Wiper Motor -- Inspection

1. INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)

Land Cruiser. Urj200, 202 Grj200 Vdj200.Wiper Washer.Wiper And Washer System (W/ Rain Sensor).Front Wiper Motor Inspection

Check the LO operation.
1. Apply battery voltage to the front wiper motor and check the speed of the front wiper motor.
  OK:
  Measurement Condition
  Specified Condition
  Battery positive (+) → Terminal 1 (+1)
  Battery negative (-) → Terminal 5 (E)
  Motor operates at low speed
  If the result is not as specified, replace the windshield wiper motor assembly.

Check the HI operation.
1. Apply battery voltage to the front wiper motor and check the speed of the front wiper motor.
  OK:
  Measurement Condition
  Specified Condition
  Battery positive (+) → Terminal 4 (+2)
  Battery negative (-) → Terminal 5 (E)
  Motor operates at high speed
  If the result is not as specified, replace the windshield wiper motor assembly.

Check the automatic stop operation.
1. Connect the positive (+) battery lead to terminal 1 (+1) of the connector and the negative (-) battery lead to terminal 5 (E). With the motor operating at low speed (LO), disconnect terminal 1 (+1) to stop the wiper motor operation at any position other than the automatic stop position.
2. Using SST, connect terminals 3 (+S) and 1 (+1). Then connect the positive (+) battery lead to terminal 2 (B) of the connector to restart the motor operation at low speed (LO).
  SST
  09843-18040
3. Check that the motor stops automatically at the automatic stop position.
  OK:
  Automatically stops.
  If the result is not as specified, replace the windshield wiper motor assembly.

2. INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)

Land Cruiser. Urj200, 202 Grj200 Vdj200.Wiper Washer.Wiper And Washer System (W/ Rain Sensor).Front Wiper Motor Inspection

Check the LO operation.
1. Apply battery voltage to the front wiper motor and check the speed of the front wiper motor.
  OK:
  Measurement Condition
  Specified Condition
  Battery positive (+) → Terminal 5 (+1)
  Battery negative (-) → Terminal 4 (E)
  Motor operates at low speed
  If the result is not as specified, replace the windshield wiper motor assembly.

Check the HI operation.
1. Apply battery voltage to the front wiper motor and check the speed of the front wiper motor.
  OK:
  Measurement Condition
  Specified Condition
  Battery positive (+) → Terminal 3 (+2)
  Battery negative (-) → Terminal 4 (E)
  Motor operates at high speed
  If the result is not as specified, replace the windshield wiper motor assembly.

Check the automatic stop operation.
1. Connect the positive (+) battery lead to terminal 5 (+1) of the connector and the negative (-) battery lead to terminal 4 (E). With the motor operating at low speed (LO), disconnect terminal 5 (+1) to stop the wiper motor operation at any position other than the automatic stop position.
2. Using SST, connect terminals 1 (+S) and 5 (+1). Then connect the positive (+) battery lead to terminal 2 (B) of the connector to restart the motor operation at low speed (LO).
  SST
  09843-18040
3. Check that the motor stops automatically at the automatic stop position.
  OK:
  Automatically stops.
  If the result is not as specified, replace the windshield wiper motor assembly.