Wiper And Washer System (W/ Rain Sensor) Front Wiper Motor Circuit

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Wiper Washer. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT WIPER MOTOR)

INSPECT FRONT WIPER MOTOR

CHECK HARNESS AND CONNECTOR (FRONT WIPER MOTOR - WINDSHIELD WIPER ECU AND BODY GROUND)

WIPER AND WASHER SYSTEM (w/ Rain Sensor) - Front Wiper Motor Circuit


DESCRIPTION

The windshield wiper ECU controls the wiper motor.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Wiper Washer.Wiper And Washer System (W/ Rain Sensor).Wiper And Washer System (W/ Rain Sensor) Front Wiper Motor Circuit


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT WIPER MOTOR)

  1. Select the Active Test, use the intelligent tester to generate a control command, and then check the front wiper motor.

    NOTICE:
    When a Body No. 5 (windshield wiper ECU) related front wiper switch is on, Active Test items related to the front wiper switch are prohibited (double operation prohibition). Check that the front wiper switches are off before performing Active Test.

    Body No. 5
    Item
    		Test Details
    		Control Range
    		Diagnostic Note
    Wiper Mot (HI)
    		Wiper motor HI operation
    		ON / OFF
    		-
    Wiper Mot (LO)
    		Wiper motor LO operation
    		ON / OFF
    		-
    OK:
    Front wiper motor operates.


NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2.INSPECT FRONT WIPER MOTOR


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Wiper Washer.Wiper And Washer System (W/ Rain Sensor).Wiper And Washer System (W/ Rain Sensor) Front Wiper Motor Circuit

  1. Remove the front wiper motor (Click here).

  1. Apply battery voltage to the front wiper motor and check the speed of the front wiper motor.

    OK:
    for LHD
    Measurement Condition
    		Specified Condition
    Battery positive (+) → Terminal 1 (+1)
    Battery negative (-) → Terminal 5 (E)
    		Motor operates at low speed
    Battery positive (+) → Terminal 4 (+2)
    Battery negative (-) → Terminal 5 (E)
    		Motor operates at high speed
    for RHD
    Measurement Condition
    		Specified Condition
    Battery positive (+) → Terminal 5 (+1)
    Battery negative (-) → Terminal 4 (E)
    		Motor operates at low speed
    Battery positive (+) → Terminal 3 (+2)
    Battery negative (-) → Terminal 4 (E)
    		Motor operates at high speed


NG
REPLACE FRONT WIPER MOTOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FRONT WIPER MOTOR - WINDSHIELD WIPER ECU AND BODY GROUND)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Wiper Washer.Wiper And Washer System (W/ Rain Sensor).Wiper And Washer System (W/ Rain Sensor) Front Wiper Motor Circuit

  1. Disconnect the A22 motor connector.

  1. Disconnect the E83 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD
    Tester Connection
    		Condition
    		Specified Condition
    A22-2 (B) - E83-8 (WIG)
    		Always
    		Below 1 Ω
    A22-1 (+1) - E83-1 (+1)
    A22-4 (+2) - E83-2 (+2)
    A22-3 (+S) - E83-7 (+SM)
    A22-5 (E) - Body ground
    A22-3 (+S) - Body ground
    		Always
    		10 kΩ or higher
    A22-2 (B) - Body ground
    A22-4 (+2) - Body ground
    A22-1 (+1) - Body ground
    for RHD
    Tester Connection
    		Condition
    		Specified Condition
    A22-2 (B) - E83-8 (WIG)
    		Always
    		Below 1 Ω
    A22-5 (+1) - E83-1 (+1)
    A22-3 (+2) - E83-2 (+2)
    A22-1 (+S) - E83-7 (+SM)
    A22-4 (E) - Body ground
    A22-1 (+S) - Body ground
    		Always
    		10 kΩ or higher
    A22-2 (B) - Body ground
    A22-3 (+2) - Body ground
    A22-5 (+1) - Body ground


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE WINDSHIELD WIPER ECU (Click here)