Outer Mirror Switch Inspection

Inspect the retract switch.

1. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Switch Condition	Specified Condition
   22 (MF) - 20 (E)	Pushed in	10 kΩ or higher
   	Not pushed in	Below 1 Ω

   If the result is not as specified, replace the outer mirror switch assembly.
   

Inspect the left/right adjustment switch.

1. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Switch Condition	Specified Condition
   13 (MSW) - 14 (E)	R	Below 10 Ω
   	OFF	10 kΩ or higher
   	L	90 to 110 Ω

   If the result is not as specified, replace the outer mirror switch assembly.
   

Inspect the mirror surface adjustment switch.

1. Select "L" on the left/right adjustment switch.
   

2. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Switch Condition		Specified Condition
   16 (M+) - 14 (E)	UP	Pressed	90 to 110 Ω
   		Not pressed	10 kΩ or higher
   	DOWN	Pressed	437 to 503 Ω
   		Not pressed	10 kΩ or higher
   	LEFT	Pressed	744 to 856 Ω
   		Not pressed	10 kΩ or higher
   	RIGHT	Pressed	225 to 275 Ω
   		Not pressed	10 kΩ or higher

   If the result is not as specified, replace the outer mirror switch assembly.
   

3. Select "R" on the left/right adjustment switch.
   

4. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Switch Condition		Specified Condition
   16 (M+) - 14 (E)	UP	Pressed	90 to 110 Ω
   		Not pressed	10 kΩ or higher
   	DOWN	Pressed	437 to 503 Ω
   		Not pressed	10 kΩ or higher
   	LEFT	Pressed	744 to 856 Ω
   		Not pressed	10 kΩ or higher
   	RIGHT	Pressed	225 to 275 Ω
   		Not pressed	10 kΩ or higher

   If the result is not as specified, replace the outer mirror switch assembly.
   

Inspect the switch illumination.
Apply battery voltage between the terminals of the light, and check the operation of the light.

OK:

Measurement Condition	Specified Condition
Battery positive (+) → Terminal 23 (ILL+) Battery negative (-) → Terminal 24 (ILL-)	Light comes on

Inspect the left/right adjustment switch and mirror surface adjustment switch.

1. Select "L" on the left/right adjustment switch.
   

2. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Switch Condition		Specified Condition
   9 (MLV) - 11 (B) 6 (M+) - 12 (E)	UP	Pressed	Below 1 Ω
   		Not pressed	10 kΩ or higher
   9 (MLV) - 12 (E) 6 (M+) - 11 (B)	DOWN	Pressed	Below 1 Ω
   		Not pressed	10 kΩ or higher
   10 (MLH) - 11 (B) 6 (M+) - 12 (E)	LEFT	Pressed	Below 1 Ω
   		Not pressed	10 kΩ or higher
   10 (MLH) - 12 (E) 6 (M+) - 11 (B)	RIGHT	Pressed	Below 1 Ω
   		Not pressed	10 kΩ or higher

   If the result is not as specified, replace the outer mirror switch assembly.
   

3. Select "R" on the left/right adjustment switch.
   

4. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Switch Condition		Specified Condition
   8 (MRV) - 11 (B) 6 (M+) - 12 (E)	UP	Pressed	Below 1 Ω
   		Not pressed	10 kΩ or higher
   8 (MRV) - 12 (E) 6 (M+) - 11 (B)	DOWN	Pressed	Below 1 Ω
   		Not pressed	10 kΩ or higher
   7 (MRH) - 11 (B) 6 (M+) - 12 (E)	LEFT	Pressed	Below 1 Ω
   		Not pressed	10 kΩ or higher
   7 (MRH) - 12 (E) 6 (M+) - 11 (B)	RIGHT	Pressed	Below 1 Ω
   		Not pressed	10 kΩ or higher

   If the result is not as specified, replace the outer mirror switch assembly.
   

Inspect the switch illumination.
Apply battery voltage between the terminals of the light, and check the operation of the light.

OK:

Measurement Condition	Specified Condition
Battery positive (+) → Terminal 15 (ILL+) Battery negative (-) → Terminal 16 (ILL-)	Light comes on