Power Mirror Control System (W/ Retract Mirror) Data List / Active Test

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Mirror (Ext). Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. READ DATA LIST

  1. PERFORM ACTIVE TEST

Power Mirror Control System (W/ Retract Mirror) -- Data List / Active Test



READ DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Data List / All Data.

  5. According to the display on the intelligent tester, read the Data List.

    Main Body
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Mirror Selection SW (R)
    		Mirror master switch signal for RH mirror / ON or OFF
    		ON: Switch is in R position
    OFF: Switch is off or in L position
    		-
    Mirror Selection SW (L)
    		Mirror master switch signal for LH mirror / ON or OFF
    		ON: Switch is in L position
    OFF: Switch is off or in R position
    		-
    Mirror Position SW (R)
    		Mirror control switch signal (right) / ON or OFF
    		ON: Right switch is on
    OFF: Any switch except right is on or all switches are off
    		-
    Mirror Position SW (L)
    		Mirror control switch signal (left) / ON or OFF
    		ON: Left switch is on
    OFF: Any switch except left is on or all switches are off
    		-
    Mirror Position SW (Up)
    		Mirror control switch signal (up) / ON or OFF
    		ON: Up switch is on
    OFF: Any switch except up is on or all switches are off
    		-
    Mirror Position SW (Dwn)
    		Mirror control switch signal (down) / ON or OFF
    		ON: Down switch is on
    OFF: Any switch except down is on or all switches are off
    		-
    Outer Mirror Fold SW
    		Mirror retract switch signal / ON or OFF
    		ON: Switch is on (retracting)
    OFF: Switch is off
    		-

    Mirror
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Mirror Memory No.1*
    		Mirror position memorized in seat memory switch memory1 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Memory No.2*
    		Mirror position memorized in seat memory switch memory2 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Memory No.3*
    		Mirror position memorized in seat memory switch memory3 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    RH Mir Position Sensor V
    		Passenger side mirror vertical sensor voltage / MIN: 0, MAX: 5 V
    		Within range from 0 to 5 V
    		-
    RH Mir Position Sensor H
    		Passenger side mirror vertical sensor voltage / MIN: 0, MAX: 5 V
    		Within range from 0 to 5 V
    		-
    LH Mir Position Sensor V
    		Driver side mirror vertical sensor voltage / MIN: 0, MAX: 5 V
    		Within range from 0 to 5 V
    		-
    LH Mir Position Sensor H
    		Driver side mirror vertical sensor voltage / MIN: 0, MAX: 5 V
    		Within range from 0 to 5 V
    		-

    HINT:
    *: w/ Seat Position Memory System

PERFORM ACTIVE TEST
HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body Electrical / Mirror / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Mirror
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    RH Mirror Up/Down
    		Mirror vertical operation
    		UP / OFF / DOWN
    		-
    RH Mirror Right/Left
    		Mirror horizontal operation
    		RIGHT / OFF / LEFT
    		-
    LH Mirror Up/Down
    		Mirror vertical operation
    		UP / OFF / DOWN
    		-
    LH Mirror Right/Left
    		Mirror horizontal operation
    		RIGHT / OFF / LEFT
    		-
    Mirror Fold
    		Mirror retract operation
    		FOLD / OFF
    		-
    Mirror Return
    		Mirror retract operation
    		RETURN / OFF
    		-