Fuel Lid Lock Control Cable Assembly (For Rhd) -- Removal |
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Remove the tonneau cover.
| 4. REMOVE INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch) |
 |
Place protective tape as shown in the illustration.
Text in Illustration *1 Protective Tape
Using a moulding remover, detach the 6 claws and remove the instrument side panel.
| 5. REMOVE INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch) |
 |
Place protective tape as shown in the illustration.
Text in Illustration *1 Protective Tape
Using a moulding remover, detach the 6 claws.
Disconnect the connector and remove the instrument side panel.
| 6. REMOVE COWL SIDE TRIM BOARD RH |
 |
Remove the cap nut.
Detach the 2 clips and remove the cowl side trim board.
| 7. REMOVE FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 8. REMOVE REAR STEP COVER |
 |
- HINT:
- Use the same procedure to remove the step cover on the other side.
Detach the 2 claws and remove the step cover.
| 9. REMOVE REAR DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 10. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE |
 |
Detach the 6 clips and remove the support plate.
| 11. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover) |
 |
- HINT:
- Use the same procedure to remove the tonneau cover holder cap on the other side.
Detach the 2 claws and remove the tonneau cover holder cap.
| 12. REMOVE REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat) |
- HINT:
- Use the same procedures described for the rear No. 2 seat cover bezel.
| 13. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH |
 |
- HINT:
- When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
Detach the 3 claws and remove the cover.
 |
Remove the bolt and rear No. 1 seat belt anchor.
 |
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Detach the 3 claws and remove the cover.
Remove the bolt and rear No. 2 seat belt anchor.
 |
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Remove the clip and bolt.
Detach the 16 clips and 2 claws.
w/o Rear Air Conditioning System:
Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.w/ Rear Air Conditioning System:
Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.
w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Remove the clip.
Detach the 16 clips and 2 claws, and remove the quarter trim panel.
w/ Tonneau Cover:
Remove the screw and clip.
Detach the 16 clips and 2 claws, and remove the quarter trim panel.
| 14. REMOVE FUEL FILLER OPENING LID LOCK RETAINER |
 |
Turn the cable counterclockwise and remove the cable from the retainer.
Turn the lock retainer counterclockwise and remove the lock retainer.
 |
| 15. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
Detach the 2 claws.
 |
Disconnect the fuel lid lock control cable and remove the fuel lid lock open lever.
| 16. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY |
Using a screwdriver, disconnect the clamps shown in the illustration.
- HINT:
- Tape the screwdriver tip before use.
Remove the lock control cable.