Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - 1GR-FE FUEL

IGNITION SWITCH EXPRESSION

DISCHARGE FUEL SYSTEM PRESSURE

FUEL SYSTEM

CHECK FOR FUEL LEAK

FUEL SYSTEM - PRECAUTION

CAUTION:

Before working on the fuel system, disconnect the cable from the negative (-) battery terminal.

Do not smoke or be near an open flame when working on the fuel system.

Keep gasoline away from rubber and leather parts.

1.IGNITION SWITCH EXPRESSION

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression	Ignition Switch (Position)	Engine Switch (Condition)
Ignition Switch off	LOCK	Off (Lock)
Ignition Switch ACC	ACC	On (ACC)
Ignition Switch ON	ON	On (IG)
Engine Start	START	On (Start)

2.DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

Disconnect the fuel pump ECU connector ().

Start the engine. After the engine has stopped on its own, turn the engine switch off.

HINT:

If DTC P0230 is output, clear the DTC ().

Crank the engine, and then check that the engine does not start.

Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work ().

When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().

Connect the fuel pump ECU connector ().

3.FUEL SYSTEM

When disconnecting the high fuel pressure line, a large amount of gasoline will spill out. Follow these procedures.

Discharge the fuel system pressure.

Put a container under the connecting part of the pressure line.

Slowly loosen the connection.

Disconnect the connection.

Plug the connection with a rubber plug.

Fuel System - Precaution. 1GR-FE FUEL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Observe these precautions when removing and installing the injectors.

Text in Illustration
*a	OK
*b	NG

Never reuse the O-ring.

When installing a new O-ring to the injector, do not damage it.

Coat new O-rings with spindle oil or gasoline before installing. Do not use engine oil, gear oil or brake oil.

Install the injector to the delivery pipe and lower intake manifold as shown in the illustration.

Text in Illustration
*1	O-Ring

NOTICE:

Before installing the injector, be sure to apply spindle oil or gasoline to the place where the delivery pipe or cylinder head contacts the O-ring of the injector.

Observe these precautions when disconnecting the fuel tube connector (for quick type A).

Fuel Pipe Clamp Type:

Remove the fuel pipe clamp from the fuel tube connector.

Text in Illustration
*1	Fuel Pipe Clamp

Fuel Hose Connector Cover Type:

Detach the lock claw by lifting up the cover as shown in the illustration.

Text in Illustration
*1	Fuel Hose Connector Cover
	Pull

Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.

Pinch the connector and disconnect the connector and pipe.

If the connector and the pipe are stuck together, pinch the connector, and then push and pull the pipe to disconnect the pipe and pull it out.

Text in Illustration
*1	Retainer
	Pinch
	Pull

NOTICE:

Do not use any tools in this procedure.

Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.

To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.

Observe these precautions when connecting the fuel tube connector (for quick type A).

Check that there is no damage or contamination in the connected part of the pipe.

Text in Illustration
	Push

Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline on the tip of the pipe.

After having finished the connection, try to pull apart the pipe and the connector to confirm that they are securely connected.

Text in Illustration
	Pull

Fuel Hose Connector Cover Type:

Attach the lock claw to the connector by pushing down on the cover.

Fuel Pipe Clamp Type:

Install the fuel pipe clamp to the connector.

Check that there is no fuel leakage.

Observe these precautions when disconnecting the fuel tube connector (for quick type B).

Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.

Text in Illustration
*1	Retainer
	Push
	Down
	Pull

Detach the 2 claws of the connector retainer. Push down on the connector and disconnect it from the pipe.

Text in Illustration
	Pull
	Push

NOTICE:

Do not use any tools in this procedure.

HINT:

If the connector and pipe are stuck, pinch the fuel pipe by hand, and push and pull the connector to disconnect it.

Check for foreign matter on the seal surface of the disconnected pipe. Clean it if necessary.

To protect the disconnected pipe and connector from damage and foreign matter, cover them with a plastic bag.

Observe these precautions when connecting the fuel tube connector (for quick type B).

Check for foreign matter on the pipe and around the connector before connecting it. Clean it if necessary.

Align the axis of the connector with the axis of the pipe. Push the pipe into the connector, and push up on the retainer.

Text in Illustration
*1	Retainer
	Up
	Push

After connecting the pipe and connector, try to pull them apart to confirm that they are securely connected.

Text in Illustration
	Pull

Observe the following precautions when disconnecting the fuel tube connector (for quick type C).

Check for dirt or mud on the fuel tube connector and pipe before disconnection. Clean if necessary.

Pull the retainer up while pinching it on both sides by hand as shown in the illustration, and disconnect the fuel tube connector from the pipe.

Text in Illustration
*1	Retainer
	Push
	Pull up
	Pull

NOTICE:

Do not use any tools.

If the fuel tube connector and pipe are stuck, pinch the fuel pipe by hand and push and pull the connector to disconnect it.

NOTICE:

Do not use any tools.

Check for dirt or mud on the pipe seal after disconnecting the fuel tube. Clean it if necessary.

Cover the disconnected fuel tube connector and pipe with a plastic bag.

NOTICE:

Do not allow the fuel tube connector or pipe to be damaged or contaminated by foreign matter.

Observe the following precautions when connecting the fuel tube connector (for quick type C).

Align the shaft of the fuel tube connector with the shaft of the pipe, push the fuel tube connector in, and push down the retainer.

Text in Illustration
*1	Retainer
	Connect
	Push down

After connecting the fuel tube connector, check that the fuel tube connector and pipe are securely connected by trying to pull them apart.

Observe these precautions when handling the nylon tube.

NOTICE:

Be careful not to turn the connection part of the nylon tube and quick connector when connecting them.

Do not kink the nylon tube.

Do not bend the nylon tube as this may cause blockage.

4.CHECK FOR FUEL LEAK

Check that there are no fuel leaks after performing maintenance anywhere on the fuel system ().

Fuel System - Precaution

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - 1GR-FE FUEL

FUEL SYSTEM - PRECAUTION