Dtc B225B Tail Gate Panel Half Switch Or Courtesy Switch Rh

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Door Hatch. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING INTELLIGENT TESTER

CHECK DTC OUTPUT

INSPECT LOWER TAIL GATE LOCK ASSEMBLY RH

CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY RH - NO. 2 MAIN BODY ECU AND BODY GROUND)

DTC B225B Tail Gate Panel Half Switch or Courtesy Switch RH


DESCRIPTION

The No. 2 main body ECU receives the half-latch switch, pawl switch and lower tail gate courtesy switch signals from the lower tail gate lock assembly RH and detects the open/closed status of the lower tail gate. DTC B225B is stored when the No. 2 main body ECU receives a half-latch switch, pawl switch or lower tail gate courtesy switch malfunction signal from the lower tail gate lock assembly RH.

DTC Code
DTC Detection Condition
Trouble Area
B225B
A half-latch switch, pawl switch or lower tail gate courtesy switch malfunction (open or short circuit) signal from the lower tail gate lock RH is received.
  1. Lower tail gate lock assembly RH
  2. Harness or connector
  3. No. 2 main body ECU

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Door Hatch.Tail Gate Closer System. Dtc B225B Tail Gate Panel Half Switch Or Courtesy Switch Rh


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER

  1. Check the Data List for proper functioning of the half-latch switch, pawl switch and lower tail gate courtesy switch (Click here).

    Body No. 4
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Half Latch Switch RH
    		Half-latch switch signal / ON or OFF
    		ON: Lower tail gate open
    OFF: Lower tail gate closed
    		-
    Courtesy Switch RH
    		Lower tail gate courtesy switch RH signal / ON or OFF
    		ON: Lower tail gate open
    OFF: Lower tail gate closed
    		-
    Luggage Pawl Switch
    		Pawl switch signal / ON or OFF
    		ON: Lower tail gate lock motor operating
    OFF: Lower tail gate open or closed
    		-
    OK:
    The display is as specified in the normal condition.


NG
Go to step 3
OK


2.CHECK DTC OUTPUT

  1. Starting with the lower tail gate closed, open and close the lower tail gate 6 times.

  1. Check for DTCs (Click here).

  1. Clear the DTCs (Click here).

  1. Starting with the lower tail gate closed, open and close the lower tail gate 6 times.

  1. Recheck for DTCs (Click here).

    OK:
    DTC B225B is not output.


NG
REPLACE NO. 2 MAIN BODY ECU (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)

3.INSPECT LOWER TAIL GATE LOCK ASSEMBLY RH

  1. Remove the lower tail gate lock assembly RH (Click here).

  1. Inspect the lower tail gate lock assembly RH (Click here).



NG
REPLACE LOWER TAIL GATE LOCK ASSEMBLY RH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY RH - NO. 2 MAIN BODY ECU AND BODY GROUND)

  1. Disconnect the h4 lower tail gate lock assembly RH connector.

  1. Disconnect the L50 No. 2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    h4-1 (HAF) - L50-8 (HAF)
    		Always
    		Below 1 Ω
    h4-2 (FUL) - L50-22 (FUL)
    		Always
    		Below 1 Ω
    h4-4 (POL) - L50-16 (POL)
    		Always
    		Below 1 Ω
    h4-3 (E1) - Body ground
    		Always
    		Below 1 Ω
    h4-1 (HAF) - Body ground
    		Always
    		10 kΩ or higher
    h4-2 (FUL) - Body ground
    		Always
    		10 kΩ or higher
    h4-4 (POL) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 2 MAIN BODY ECU (Click here)