Power Window Regulator Motor (For Rear Door) -- Installation |
- HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
- A bolt without a torque specification is shown in the standard bolt chart (Click here).
| 1. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY |
Apply MP grease to the sliding and rotating areas of the regulator motor.
Using a T25 "TORX" driver, install the motor with the 3 screws.
- Torque:
- 5.4 N*m{55 kgf*cm, 48 in.*lbf}
- HINT:
- A new rear window regulator motor uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
| 2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Apply MP grease to the sliding parts of the rear door window regulator sub-assembly LH.
Text in Illustration *a Temporary Bolt
 |
Loosely install the temporary bolt onto the rear door window regulator sub-assembly LH.
Insert the rear door window regulator sub-assembly LH into the door panel. Use the temporary bolt to hang the rear door window regulator sub-assembly LH on the door panel.
- NOTICE:
- Be careful not to drop the rear door window regulator sub-assembly LH as it may become damaged.
Temporarily install the rear door window regulator sub-assembly LH with the 3 bolts.
Tighten the 4 bolts in the order shown in the illustration.
- Torque:
- 8.0 N*m{82 kgf*cm, 71 in.*lbf}
| 3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
Slide the rear door glass sub-assembly LH as shown in the illustration to install it.
 |
| 4. INSTALL REAR DOOR QUARTER WINDOW GLASS |
Install the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH in the direction indicated by the arrow in the illustration.
 |
| 5. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY |
Install the rear door rear lower window frame sub-assembly LH with the 2 bolts and screw.
| 6. INSTALL REAR DOOR GLASS RUN |
Install the rear door glass run LH.
| 7. INSTALL REAR DOOR SERVICE HOLE COVER |
Apply butyl tape to the door.
Pass the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH through a new rear door service hole cover LH.
- NOTICE:
- When installing the rear door service hole cover LH, pull the links and connectors through the rear door service hole cover LH.
- There should be no wrinkles or folds after attaching the rear door service hole cover LH.
- After attaching the rear door service hole cover LH, check the sealing quality.
 |
Connect the 3connectors.
 |
Attach the 7clamps.
Install the bolt as shown in the illustration.
- Torque:
- 8.4 N*m{86 kgf*cm, 74 in.*lbf}
 |
| 8. INSTALL REAR SPEAKER SET (w/ Rear Speaker) |
Temporarily install the speaker by attaching the claw of the speaker to the door panel.
 |
Install the speaker with the 3 screws.
- NOTICE:
- Do not touch the cone part of the speaker.
Connect the connector.
| 9. INSTALL REAR INNER DOOR GLASS WEATHERSTRIP |
Install the rear door inner glass weatherstrip LH to the door panel.
 |
| 10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
Connect the connector.
Connect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH to the rear door inside handle sub-assembly LH.
 |
Attach the 4 claws and pin.
 |
Attach the 9 clips to install the rear door trim board sub-assembly LH.
Install the 3 screws.
| 11. INSTALL ASSIST GRIP COVER |
Attach the 9 claws to install the assist grip cover LH to the rear door trim board sub-assembly LH.
| 12. INSTALL REAR DOOR UPPER ARMREST BASE PANEL |
Connect the connector.
Attach the 7 claws to install the rear door upper armrest base panel assembly LH.
 |
| 13. INSTALL REAR DOOR INSIDE HANDLE BEZEL |
Attach the 4 claws to install the rear door inside handle bezel LH.
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).