Rear Seat Cushion Heater (For 60/40 Split Seat Type 60 Side) Installation

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200

Seat. Land Cruiser. Urj200, 202 Grj200 Vdj200

Rear Seat Cushion Heater (For 60/40 Split Seat Type 60 Side) -- Installation

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.

1. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY

Land Cruiser. Urj200, 202 Grj200 Vdj200.Seat.Front Power Seat Control System (W/ Seat Position Memory System).Rear Seat Cushion Heater (For 60/40 Split Seat Type 60 Side) Installation

Set the rear seat cushion heater assembly onto the rear separate type seat cushion cover so that the name stamp is facing the rear seat cushion pad LH.

Install the seat cushion heater with new tack pins.

2. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

Land Cruiser. Urj200, 202 Grj200 Vdj200.Seat.Front Power Seat Control System (W/ Seat Position Memory System).Rear Seat Cushion Heater (For 60/40 Split Seat Type 60 Side) Installation

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
NOTICE:
1. Be careful not to damage the cover.
2. When installing the hog rings, avoid wrinkling the cover.

Land Cruiser. Urj200, 202 Grj200 Vdj200.Seat.Front Power Seat Control System (W/ Seat Position Memory System).Rear Seat Cushion Heater (For 60/40 Split Seat Type 60 Side) Installation

Attach the 3 pieces of fastening tape.

3. INSTALL SEAT CUSHION COVER WITH PAD

Install the seat cushion cover with pad.

w/ Rear Seat Side Airbag:
Pass the side airbag wire harness through the hole in the seat cushion.

w/ Seat Heater System:
1. Pass the seatback heater wire harness through the hole in the seat cushion.
2. Connect the 2 seat heater connectors.

w/ Rear Seat Side Airbag:
Attach the side airbag wire harness clamps.

4. CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

Land Cruiser. Urj200, 202 Grj200 Vdj200.Seat.Front Power Seat Control System (W/ Seat Position Memory System).Rear Seat Cushion Heater (For 60/40 Split Seat Type 60 Side) Installation

Connect the belt anchor.
NOTICE:
Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

5. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

Land Cruiser. Urj200, 202 Grj200 Vdj200.Seat.Front Power Seat Control System (W/ Seat Position Memory System).Rear Seat Cushion Heater (For 60/40 Split Seat Type 60 Side) Installation

Install the belt with the bolt.
Torque:
42 N*m{428 kgf*cm, 31 ft.*lbf}
NOTICE:
Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.
HINT:
The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, connect it when installing the rear No. 1 seat inner belt LH.

6. INSTALL REAR SEAT UNDER TRAY COVER LH

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the 4 claws to install the cover.

Install the 2 screws.

7. INSTALL REAR SEAT CUSHION COVER RH

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the 2 claws to install the cover.

Install the 4 screws.

8. INSTALL REAR UNDER SIDE COVER LH

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the 2 claws and 2 clips to install the cover.

Install the 5 screws.

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the 10 claws.

9. INSTALL REAR SEATBACK STAY COVER LH

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the 2 claws to install the cover.

Install the screw.

10. INSTALL SEAT BELT ANCHOR COVER CAP

Land Cruiser. Urj200, 202 Grj200 Vdj200

Install the anchor cover cap with the screw.

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the claw to close the cap.

11. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

Land Cruiser. Urj200, 202 Grj200 Vdj200

Install the hinge with the 2 nuts.
Torque:
42 N*m{428 kgf*cm, 31 ft.*lbf}

12. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the cable clamp to connect the cable.

Land Cruiser. Urj200, 202 Grj200 Vdj200

Install the hinge with the 2 nuts.
Torque:
42 N*m{428 kgf*cm, 31 ft.*lbf}

w/ Rear Seat Side Airbag:
Attach the wire harness clamp.

w/ Seat Heater System:
Attach the wire harness clamp.

13. INSTALL REAR NO. 2 SEAT PROTECTOR

Install the wire harness, and attach 2 claws to close the protector.

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the claw to install the protector to the seat hinge.

Install the clip.

Land Cruiser. Urj200, 202 Grj200 Vdj200

w/ Rear Seat Side Airbag:
Attach the claw to install the wire harness connector.

w/ Seat Heater System:
Attach the claw to install the wire harness connector.

14. INSTALL REAR NO. 2 SEAT LEG SIDE COVER

Land Cruiser. Urj200, 202 Grj200 Vdj200

Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the 4 claws to install the seat leg side cover.

Install the 4 screws.

15. INSTALL UPPER SEAT TRACK RAIL COVER RH

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the 2 claws to install the cover.

16. INSTALL UPPER SEAT TRACK RAIL COVER LH

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the 2 claws to install the cover.

17. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the 4 claws to install the cover.

Install the 2 screws.

18. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

Attach the guide to install the rear seat No. 1 reclining cover LH.

Install the screw.

19. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

Land Cruiser. Urj200, 202 Grj200 Vdj200

Install the release handle with the screw.

20. INSTALL SEAT ADJUSTER BOLT COVER

Land Cruiser. Urj200, 202 Grj200 Vdj200

Attach the 2 claws to install the cover.

21. INSTALL REAR NO. 1 SEAT ASSEMBLY LH

Install the rear No. 1 seat assembly (Click here).