Rear No. 1 Seat Assembly (For 60/40 Split Seat Type 40 Side) Reassembly

Install the lock control lever with the bolt.

Torque:

13 N*m{133 kgf*cm, 10 ft.*lbf}

Temporarily install the seat cushion frame with the 5 nuts and bolt.

Tighten the 5 nuts.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

Using a T40 "TORX" socket, tighten the bolt.

Torque:

21 N*m{214 kgf*cm, 15 ft.*lbf}

Install the belt with the bolt.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

NOTICE:

Do not overlap the anchor part of the seat belt and protruding parts of the seat.

Attach the 2 claws to install the seat heater control.

Install the holder bracket with the 2 screws.

Connect the seat wire connector.

Attach the clamp to install the seat lock cable.

Attach the 3 cable clamps to connect the 3 cables.

Install the lower seat track bracket with the 2 nuts.

Torque:

21 N*m{214 kgf*cm, 15 ft.*lbf}

Install the lower seat track bracket with the 2 nuts.

Torque:

21 N*m{214 kgf*cm, 15 ft.*lbf}

Install the 2 fold seat lock control cables.

Attach the 2 cable clamps to connect the 2 cables.

Temporarily install the seatback frame with the 4 bolts.

Using a T40 "TORX" socket, tighten the 4 bolts.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

Attach the clamp to install the lock control cable.

Attach the 2 cable clamps to connect the cable.

Attach the clamp to install the adjusting cable.

Attach the 2 cable clamps to connect the cable.

Attach the claw to install the cover.

Install the screw.

Attach the clamp to install the cover.

Install the screw.

Attach the claw to install the cover.

Install the screw.

Attach the claw to install the cover.

Install the screw.

Set the rear seatback heater assembly onto the rear separate type seatback cover so that the name stamp is facing the rear seatback pad RH.

Install the seatback heater with new tack pins.

Using hog ring pliers, install the seatback cover with new hog rings.

NOTICE:

1. Be careful not to damage the cover.
   
2. When installing the hog rings, avoid wrinkling the cover.
   

w/ Rear Seat Side Airbag:
Connect the seatback cover bracket to the seatback pad.

Install the seatback cover with pad.

w/ Rear Seat Side Airbag:
Pass the side airbag wire harness through the hole in the seatback.

w/ Seat Heater System:

1. Pass the seatback heater wire harness through the hole in the seatback.
   





2. Connect the seatback heater wire harness and install a new cable tie.
   

w/ Rear Seat Side Airbag:
Install the seatback cover bracket to the seat frame with the cap nut.

Torque:

5.5 N*m{56 kgf*cm, 49 in.*lbf}

CAUTION:

After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

Using hog ring pliers, install new hog rings to the seatback frame.

Attach the 4 claws to install the 2 supports.

Push the board down to attach the 2 claws on the bottom.

Attach the 2 claws on the top of the board to install it.

Attach the 4 claws to install the cover.

Set the rear seat cushion heater assembly onto the rear separate type seat cushion cover so that the name stamp is facing the rear seat cushion pad RH.

Install the seat cushion heater with new tack pins.

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

NOTICE:

1. Be careful not to damage the cover.
   
2. When installing the hog rings, avoid wrinkling the cover.
   

Attach the 3 pieces of fastening tape.

Install the seat cushion cover with pad.

w/ Rear Seat Side Airbag:
Pass the side airbag wire harness through the hole in the seat cushion.

w/ Seat Heater System:

1. Pass the seatback heater wire harness through the hole in the seat cushion.
   





2. Connect the 2 seat heater connectors.
   

w/ Rear Seat Side Airbag:
Attach the side airbag wire harness clamps.

Attach the cable clamp to connect the cable.

Attach the 2 cable clamps to connect the 2 cables.

Install the seat track handle with the 2 screws.

Attach the 4 claws to install the cover.

Install the 2 screws.

Attach the 3 claws to install the seat cushion plate.

Attach the 2 claws and clip to install the cover.

Install the 5 screws.

Attach the 2 claws to install the cover.

Install the 3 screws.

Attach the 12 claws.

Attach the cable clamp to connect the cable.

Install the hinge with the 2 nuts.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

w/ Rear Seat Side Airbag:
Attach the wire harness clamp.

w/ Seat Heater System:
Attach the wire harness clamp.

Install the hinge with the 2 nuts.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

Install the wire harness, and attach the 2 claws to close the protector.

Attach the claw to install the protector to the seat hinge.

Install the clip.

w/ Rear Seat Side Airbag:
Attach the claw to install the wire harness connector.

w/ Seat Heater System:
Attach the claw to install the wire harness connector.

Attach the clip to install the cover.

Attach the clip to install the cover.

Attach the 6 claws to install the 2 covers.

Install the fold seat stopper band to the seat leg side cover.

Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

Attach the 3 claws to install the seat leg side cover.

Install the 4 screws.

Attach the 4 claws to install the 2 covers.

Attach the 2 claws to install the cover.

Attach the 2 claws to install the cover.

Attach the 4 claws to install the cover.

Install the 2 screws.

Attach the 3 claws in the order shown in the illustration to install the cover.

Install the 2 screws.

Install the release handle with the screw.

Attach the 2 claws to install the cover.