REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Split Bench Seat Type)
REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH (w/ Sliding Roof)
REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH (w/o Sliding Roof)
Rear Airbag Sensor -- Removal |
- HINT:
- Use the same procedures for the LH side and RH side.
- The procedures listed below are for the LH side.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 2. REMOVE REAR NO. 2 SEAT ASSEMBLY LH |
Remove the rear No. 2 seat assembly LH (Click here).
| 3. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Split Bench Seat Type) |
Remove the rear No. 2 seat assembly LH (Click here).
| 4. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/ Sliding Roof) |
 |
Detach the 6 clips and remove the rear floor mat support plate.
| 5. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Sliding Roof) |
|
Detach the 6 clips and remove the rear floor mat support plate.
| 6. REMOVE REAR STEP COVER (w/ Sliding Roof) |
- HINT:
- Use the same procedure for both rear step covers.
Detach the 2 claws and remove the rear step cover.
 |
| 7. REMOVE REAR STEP COVER (w/o Sliding Roof) |
- HINT:
- Use the same procedure for both rear step covers.
Detach the 2 claws and remove the rear step cover.
|
| 8. REMOVE REAR DOOR SCUFF PLATE LH (w/ Sliding Roof) |
 |
Remove the screw.
Detach the 3 claws and 4 clips, and remove the rear door scuff plate LH.
| 9. REMOVE REAR DOOR SCUFF PLATE LH (w/o Sliding Roof) |
|
Remove the screw.
Detach the 3 claws and 4 clips, and remove the rear door scuff plate LH.
| 10. REMOVE REAR SEAT COVER CAP (w/ Sliding Roof) |
- HINT:
- Use the same procedure for both No. 1 luggage compartment trim hooks.
Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *a Protective Tape
 |
| 11. REMOVE REAR SEAT COVER CAP (w/o Sliding Roof) |
- HINT:
- Use the same procedure for both No. 1 luggage compartment trim hooks.
Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *a Protective Tape
|
| 12. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH (w/ Sliding Roof) |
 |
- HINT:
- When removing the front quarter trim panel assembly LH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
Detach the 3 claws and remove the outer lap belt anchor cover.
 |
Remove the bolt and rear No. 1 seat belt anchor.
 |
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Remove the bolt and rear No. 2 seat belt anchor.
 |
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Remove the clip and bolt.
Detach the 18 clips and 2 claws.
w/o Rear Air Conditioning System:
Disconnect the rear seat lock control lever cable and then remove the front quarter trim panel assembly LH.w/ Rear Air Conditioning System:
Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the front quarter trim panel assembly LH.
w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Remove the clip.
Detach the 18 clips and 2 claws, and remove the front quarter trim panel assembly LH.
| 13. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH (w/o Sliding Roof) |
|
- HINT:
- When removing the front quarter trim panel assembly LH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
Detach the 3 claws and remove the outer lap belt anchor cover.
|
Remove the bolt and rear No. 1 seat belt anchor.
|
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Remove the bolt and rear No. 2 seat belt anchor.
|
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Remove the clip and bolt.
Detach the 18 clips and 2 claws.
w/o Rear Air Conditioning System:
Disconnect the rear seat lock control lever cable and then remove the front quarter trim panel assembly LH.w/ Rear Air Conditioning System:
Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the front quarter trim panel assembly LH.
w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Remove the clip.
Detach the 18 clips and 2 claws, and remove the front quarter trim panel assembly LH.
w/ Tonneau Cover:
Remove the screw and clip.
Detach the 18 clips and 2 claws, and remove the front quarter trim panel assembly LH.
| 14. REMOVE REAR AIRBAG SENSOR |
Remove the bolt and rear airbag sensor.
 |
Disconnect the connector.