CHECK FRONT SEAT OUTER BELT RH (FRONT PRETENSIONER SQUIB RH)
CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)
DTC B1900/73 Short in Front Pretensioner Squib RH Circuit |
DTC B1901/73 Open in Front Pretensioner Squib RH Circuit |
DTC B1902/73 Short to GND in Front Pretensioner Squib RH Circuit |
DTC B1903/73 Short to B+ in Front Pretensioner Squib RH Circuit |
DESCRIPTION
The front pretensioner squib RH circuit consists of the center airbag sensor and the front seat outer belt RH.This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
| B1900/73 | When one of the following conditions is met:
|
|
| B1901/73 | When one of the following conditions is met:
|
|
| B1902/73 | When one of the following conditions is met:
|
|
| B1903/73 | When one of the following conditions is met:
|
|
WIRING DIAGRAM
INSPECTION PROCEDURE
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
- HINT:
- To perform the simulation method, enter the check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (Click here).
| 1.CHECK FRONT SEAT OUTER BELT RH (FRONT PRETENSIONER SQUIB RH) |
Turn the ignition switch off.
 |
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the front seat outer belt RH.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
- CAUTION:
- Never connect the tester to the front seat outer belt RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- Insert SST straight into the terminals of the connector.
- SST
- 09843-18061
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1900, B1901, B1902 or B1903 is not output.
- HINT:
- Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the No. 2 floor wire connector (on the front seat outer belt RH side) is not damaged.
- OK:
- The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
|
| ||||
| OK | |
| 3.CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT) |
Disconnect the connectors from the center airbag sensor.
 |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection Switch Condition Specified Condition L13-1 (R+) - Body ground Ignition switch ON Below 1 V L13-2 (R-) - Body ground Ignition switch ON Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition L13-1 (R+) - L13-2 (R-) Always Below 1 Ω
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition L13-1 (R+) - L13-2 (R-) Always 1 MΩ or higher L13-1 (R+) - Body ground Always 1 MΩ or higher L13-2 (R-) - Body ground Always 1 MΩ or higher
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR |
Connect the connectors to the front seat outer belt RH and the center airbag sensor.
 |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1900, B1901, B1902 or B1903 is not output.
- HINT:
- Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.
|
| ||||
| OK | ||
| ||