Meter / Gauge System Data List / Active Test

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Meter Gauge Display. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. DATA LIST

  1. ACTIVE TEST

Meter / Gauge System -- Data List / Active Test



DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body Electrical, Powertrain or Chassis / (desired system) / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Combination Meter
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    ODO/TRIP Change SW
    		Trip switch (ODO/TRIP switch) condition / ON or OFF
    		ON: Trip switch (ODO/TRIP switch) pushed
    OFF: Trip switch (ODO/TRIP switch) not pushed
    		-
    Tail Cancel SW
    		TAIL cancel switch condition / ON or OFF
    		ON: TAIL cancel switch on
    OFF: TAIL cancel switch off
    		-
    Washer Switch
    		Washer switch / ON or OFF
    		ON: Washer switch on
    OFF: Washer switch off
    		-
    P-Seatbelt Buckle SW
    		Front passenger side seat belt warning light request signal / ON or OFF
    		ON: Tongue plate (for front passenger side) inserted
    OFF: Tongue plate (for front passenger side) not inserted
    		-
    Oil Level SW
    		Oil level switch / ON or OFF
    		ON: Oil level switch on
    OFF: Oil level switch off
    		-
    Water Level SW
    		Water level switch / ON or OFF
    		ON: Water level switch on
    OFF: Water level switch off
    		-
    Multi Display Select Switch
    		Steering multi-display select switch / ON or OFF
    		ON: Steering multi-display select switch on
    OFF: Steering multi-display select switch off
    		-
    Vehicle Speed Meter
    		Vehicle speed / Min.: 0 (0), Max.: 255 (158)
    		Almost same as actual vehicle speed (when driving)
    		Unit: km/h (mph)
    Engine Rpm
    		Engine speed / Min.: 0, Max.: 12750
    		Idling: 700 to 800
    		Unit: rpm
    Coolant Temperature
    		Engine coolant temperature / Min.: -40 (-40), Max.: 140 (284)
    		After warming up: 80 to 105 (176 to 221)
    1. Unit: °C (°F).
    2. If the value is -40 (-40): The sensor circuit is open.
    3. If the value is 140 (284): The sensor circuit is shorted.
    Fuel Input
    		Fuel sender gauge input / Min.: 0, Max.: 127.5
    		Fuel sender input value
    		Unit: L
    Rheostat value
    		Light control rheostat switch input / Min.: 0, Max.: 100
    		Light control rheostat switch is fully turned right (0) → fully turned left (100)
    		Unit: %
    Communication ECM/Meter DTC 3
    		ECM communication stop history / Rec or Unrec
    		Rec: DTC is stored
    Unrec: DTC is not stored
    		-
    ECM ODO (History 3)
    		ECM odometer history / Min.: 0, Max.: 999999
    		With history: 0 to 999999
    Without history: ffffffh
    		-
    Communication ECM/Meter DTC 2
    		ECM communication stop history / Rec or Unrec
    		Rec: DTC is stored
    Unrec: DTC is not stored
    		-
    ECM ODO (History 2)
    		ECM odometer history / Min.: 0, Max.: 999999
    		With history: 0 to 999999
    Without history: ffffffh
    		-
    Communication ECM/Meter DTC 1
    		ECM communication stop history / Rec or Unrec
    		Rec: DTC is stored
    Unrec: DTC is not stored
    		-
    ECM ODO (History 1)
    		ECM odometer history / Min.: 0, Max.: 999999
    		With history: 0 to 999999
    Without history: ffffffh
    		-
    Communication ABS/Meter DTC 3
    		Skid control ECU communication stop history / Rec or Unrec
    		Rec: DTC is stored
    Unrec: DTC is not stored
    		-
    ABS/VSC ODO (History 3)
    		Skid control ECU odometer history / Min.: 0, Max.: 999999
    		With history: 0 to 999999
    Without history: ffffffh
    		-
    Communication ABS/Meter DTC 2
    		Skid control ECU communication stop history / Rec or Unrec
    		Rec: DTC is stored
    Unrec: DTC is not stored
    		-
    ABS/VSC ODO (History 2)
    		Skid control ECU odometer history / Min.: 0, Max.: 999999
    		With history: 0 to 999999
    Without history: ffffffh
    		-
    Communication ABS/Meter DTC 1
    		Skid control ECU communication stop history / Rec or Unrec
    		Rec: DTC is stored
    Unrec: DTC is not stored
    		-
    ABS/VSC ODO (History 1)
    		Skid control ECU odometer history / Min.: 0, Max.: 999999
    		With history: 0 to 999999
    Without history: ffffffh
    		-
    Units By Region
    		Unit of display setting / Km/l JP, Km/l, Mi/g US or Mi/g UK
    		Displays unit setting
    		-
    Language
    		Language of display setting / English, Spanish, French*, German* or Italian*
    		Displays language setting
    		-
    Driver Side Seatbelt Warning Buzzer
    		Driver side seat belt warning buzzer setting / ON or OFF
    		ON: Driver side seat belt warning buzzer on setting
    OFF: Driver side seat belt warning buzzer off setting
    		-
    P-Seatbelt Warning Buzzer
    		Front passenger side seat belt warning buzzer setting / ON or OFF
    		ON: Front passenger side seat belt warning buzzer on setting
    OFF: Front passenger side seat belt warning buzzer off setting
    		-
    Sub Fuel Input
    		Fuel sender gauge input / Min.: 0, Max.: 127.5
    		Fuel sender input value
    		Unit: L
    Integrated value for Oil Maintenance
    		Oil maintenance warning integrated value / Min.: 0 (0), Max.: 25500 (41037)
    		0 (0) to 25500 (41037)
    		Unit: mile
    Integrated value for Timing belt
    		T-belt indicator integrated value / Min.: 0, Max.: 6553500
    		0 to 6553500
    		Unit: km/h
    +B Voltage Value
    		+B voltage / Min.: 0, Max.: 25.5
    		11 to 14
    		Unit: V
    Coolant Temperature
    		Engine coolant temperature / Min.: -40 (-40), Max.: 140 (284)
    		After warming up: 80 to 105 (176 to 221)
    1. Unit: °C (°F)
    2. If the value is -40 (-40): The sensor circuit is open.
    3. If the value is 140 (284): The sensor circuit is shorted.

    Engine
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Engine Rpm
    		Engine speed / Min.: 0, Max.: 16383.75
    		Idling: 700 to 800
    		Unit: rpm
    Vehicle Speed Meter
    		Vehicle speed / Min.: 0 (0), Max.: 255 (158)
    		Actual vehicle speed
    1. Unit: km/h (mph)
    2. The speed is indicated on the speedometer.
    Coolant Temperature*1
    		Engine coolant temperature:
    Min.: -40°C, Max.: 140°C
    		80 to 100°C (176 to 212):
    After warming up
    1. If the value is -40°C (-40°F), The sensor circuit is open.
    2. If the value is 140°C (284°F) or higher, The sensor circuit is shorted.
    Coolant Temperature*2
    		Engine coolant temperature /
    Min.: -40°C, Max.: 140°C
    		After warming up engine: 75 to 90°C (167 to 194°F)
    1. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
    2. After a long soak, the coolant temperature, intake air temperature, and ambient air temperature are approximately equal.

    HINT:
    *1: except 1VD-FTV
    *2: for 1VD-FTV

ACTIVE TEST
HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body Electrical / (Combination Meter) / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Combination Meter
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Speed Meter Operation*1
    		Speedometer
    		0, 40, 80, 120, 160, 200, 240 or 280
    		Perform the test with the vehicle stopped and engine idling.
    Tachometer operation
    		Tachometer
    		0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000
    		Perform the test with the vehicle stopped and engine idling.
    Fuel Meter Operation
    		Fuel receiver gauge
    		EMPTY, 1/4, FULL
    		Perform the test with the vehicle stopped and engine idling.
    Volt Meter Operation
    		Voltmeter
    		0, 3, 6, 9, 12, 15 or 18
    		Perform the test with the vehicle stopped and engine idling.
    Oil Pressure Meter Operation
    		Oil pressure receiver gauge
    		LOW, 1/4, 1/2, 3/4 or HIGH
    		Perform the test with the vehicle stopped and engine idling.
    A/T Indicator operation (1)*10
    		A/T indicator (normal mode)
    		P, R, N, D, 4, 3, 2, L
    		Perform the test with the vehicle stopped and engine idling.
    A/T Indicator operation (2)*10
    		A/T indicator (sequential mode)
    		Es, 5 or 6
    		Perform the test with the vehicle stopped and engine idling.
    Meter Display 1*2
    		All dots in the multi-information display
    		ALL, 0, 1, 2, 3, 4, 5 or 6
    		Perform the test with the vehicle stopped and engine idling.
    Meter Display 2*2
    		All dots in the multi-information display
    		7, 8 or 9
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Beam
    		BEAM indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Head
    		HEAD indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Tail
    		TAIL indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Fr FOG
    		FRONT FOG indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Airbag
    		SRS warning light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Precrash
    		PCS indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Driver Side Seat Belt
    		Driver side seat belt warning light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Front Passenger Side Seat Belt
    		Passenger side seat belt warning light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Doors All Open
    		All doors open light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Washer
    		Multi-information display
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Fuel
    		Low fuel warning light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Charge
    		CHARGE warning light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp ABS
    		ABS warning light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Slip*6
    		SLIP indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Tire Pressure Warning System*11
    		Tire pressure warning light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Brake
    		Brake warning light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp oil Level
    		Multi-information display
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp ECT PWR
    		ECT PWR indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    A/T Oil Temperature Operation*10
    		Multi-information display
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Cruise*7
    		Cruise control indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. KEY
    		Multi-information display
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Master Warning
    		Master warning light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Clearance Sonar LCD
    		Multi-information display
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. INTUITIVE P/A LCD
    		Multi-information display
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp VSC OFF*6
    		Multi-information display
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. 2nd START
    		2nd START indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Ctr DIFF LOCK
    		Center differential lock indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. 4LO
    		4LO indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. CRAWL*6
    		CRAWL indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. A/T P*10
    		A/T P indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Water Temperature Meter Operation
    		Engine coolant temperature receiver gauge
    		LOW, NORMAL or HIGH
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. GLOW*5
    		Glow indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Water Level
    		Fuel filter and sedimenter indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Over Speed
    		Speed limit indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    VSC TRC Indicator*6
    		TRC OFF indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    PPS Indicator
    		Power steering warning light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. ECONO
    		Eco driving indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. SET*7
    		SET indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Radar Cruise Indicator*3
    		Radar cruise control indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Rr Inner Wheel Control Indicator*6
    		Turn assist indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    OFF Road Guidance Indicator*8
    		Multi-terrain select indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Indicat. Headlamp Auto Leveling*4
    		Headlight beam level control system warning light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.
    Automatic High Beam Indicator*9
    		Automatic High Beam Indicator light
    		ON or OFF
    		Perform the test with the vehicle stopped and engine idling.

    HINT:
    *1:
    1. The doors will be locked automatically when performing the speedometer Active Test. This is a normal function.
    2. The displayed value has the same units (km/h, mph) as the main scale of the vehicle speedometer.
    3. The needle position should be within the acceptable range.
    *2: If this Active Test is being performed and the ignition switch is turned off and then ON, the A/T and ODO/TRIP display background may turn white. If this occurs, end this Active Test and turn the ignition switch off.
    *3: w/ Dynamic Radar Cruise Control System
    *4: w/ Headlight Leveling
    *5: for 1VD-FTV
    *6: w/ VSC
    *7: w/ Cruise Control System
    *8: w/ Multi-terrain Select
    *9: w/ Automatic High Beam System
    *10: for Automatic Transmission
    *11: w/ Tire Pressure Warning System

Main Body
Tester Display
Test Part
Control Range
Diagnostic Note
Dimmer Signal
Illumination dimming operation
ON or OFF
-