Entry Lock And Unlock Switch (For Front) Removal

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  2. REMOVE FRONT LOWER DOOR FRAME BRACKET GARNISH LH

  3. REMOVE FRONT DOOR ARMREST BASE PANEL ASSEMBLY LH

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

  5. REMOVE DOOR ASSIST GRIP COVER LH

  6. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  8. REMOVE FRONT DOOR SERVICE HOLE COVER LH

  9. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH

  10. REMOVE FRONT DOOR HANDLE ASSEMBLY OUTSIDE LH

Entry Lock And Unlock Switch (For Front) -- Removal


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT LOWER DOOR FRAME BRACKET GARNISH LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the clip and claw, and remove the front door lower frame bracket garnish LH.



3. REMOVE FRONT DOOR ARMREST BASE PANEL ASSEMBLY LH


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a moulding remover, detach the 5 claws.

  1. Disconnect the connector and remove the armrest base panel.



4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry Lock And Unlock Switch (For Front) Removal

  1. Using a screwdriver, detach the 4 claws and remove the front door inside handle bezel LH.

    HINT:
    Tape the screwdriver tip before use.
    Text in Illustration
    *1
    		Protective Tape


5. REMOVE DOOR ASSIST GRIP COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a moulding remover, detach the 8 claws and remove the door assist grip cover LH.



6. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the claw.

  1. Remove the courtesy light and then disconnect the connector.



7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry Lock And Unlock Switch (For Front) Removal

  1. Remove the 3 screws.

  1. Remove the 13 clips.

  1. Remove the front inner door glass weatherstrip LH together with the front door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

    HINT:
    Make sure that the pin labeled A in the illustration is detached from the door panel.

  1. Disconnect the connector.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Disconnect the 2 cables from the front door inside handle sub-assembly LH.



8. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a clip remover, detach the 9 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the front door service hole cover LH.

    HINT:
    Remove the remaining tape on the door.


9. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the hole plug.

  1. Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover LH with the door lock cylinder installed.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the 2 claws and remove the front door outside handle cover LH.



10. REMOVE FRONT DOOR HANDLE ASSEMBLY OUTSIDE LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Disconnect the connector.

  1. Using a T30 "TORX" wrench, loosen the screw.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.

    NOTICE:
    If the release plate is not pulled and held when removing the handle, the release plate will interfere with the handle and become damaged.