Theft Deterrent System (W/ Entry And Start System) Security Indicator Light Circuit

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)

CHECK VEHICLE EQUIPMENT

CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)

CHECK HARNESS AND CONNECTOR (CLOCK - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)

THEFT DETERRENT SYSTEM (w/ Entry and Start System) - Security Indicator Light Circuit


DESCRIPTION

  1. When the theft deterrent system is in the disarmed state, the security indicator will flash continuously if the immobiliser system is set, or not illuminate if the immobiliser system is not set.
    When the theft deterrent system is in the armed state, the immobiliser system is automatically set and the security indicator will flash continuously.
    When the theft deterrent system is in the arming preparation state and alarm sounding state, the certification ECU (smart key ECU assembly) causes the security indicator to be illuminated.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Theft Deterrent System (W/ Entry And Start System) Security Indicator Light Circuit


Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Theft Deterrent System (W/ Entry And Start System) Security Indicator Light Circuit


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry&Start / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Entry&Start
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Security Indicator
    		Security indicator
    		ON / OFF
    		-
    OK:
    Security indicator illuminates.


NG
Go to step 2
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

2.CHECK VEHICLE EQUIPMENT

  1. Check if the multi-display is equipped on the vehicle.

    Result
    Result
    		Proceed to
    w/ Multi-display
    		A
    w/o Multi-display
    		B


B
Go to step 5
A


3.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)

  1. Disconnect the F79 multi-display assembly connector.

  1. Disconnect the E29 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    F79-10 (SEUC) - E29-2 (IND)
    		Always
    		Below 1 Ω
    F79-13 (GND1) - Body ground
    		Always
    		Below 1 Ω
    F79-10 (SEUC) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)

  1. Disconnect the F79 multi-display assembly connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry & Start / Active Test.

  1. Operate the certification ECU (smart key ECU assembly) using the active test function and measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    		Tester Operation
    		Specified Condition
    E29-2 (IND) - Body ground
    		Security Indicator ON
    		11 to 14 V
    E29-2 (IND) - Body ground
    		Security Indicator OFF
    		Below 1 V
    HINT:
    Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

REPLACE MULTI-DISPLAY (Click here)

5.CHECK HARNESS AND CONNECTOR (CLOCK - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)

  1. Disconnect the g1 clock connector.

  1. Disconnect the E29 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    g1-9 (LP) - E29-2 (IND)
    		Always
    		Below 1 Ω
    g1-1 (E) - Body ground
    		Always
    		Below 1 Ω
    g1-9 (LP) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)

  1. Disconnect the g1 clock connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry & Start / Active Test.

  1. Operate the certification ECU (smart key ECU assembly) using the active test function and measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    		Tester Operation
    		Specified Condition
    g1-9 (LP) - Body ground
    		Security Indicator ON
    		11 to 14 V
    g1-9 (LP) - Body ground
    		Security Indicator OFF
    		Below 1 V
    HINT:
    Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

REPLACE CLOCK (Click here)