Entry And Start System (For Entry Function) Front Passenger Side Door Entry Lock Function Does Not Operate

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK POWER DOOR LOCK CONTROL SYSTEM

READ VALUE USING GTS (P-DOOR TRIGGER SWITCH)

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE ASSEMBLY [FOR FRONT PASSENGER DOOR])

CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (INPUT TO FRONT PASSENGER DOOR LOCK SENSOR)

ENTRY AND START SYSTEM (for Entry Function) - Front Passenger Side Door Entry Lock Function does not Operate


DESCRIPTION

If the entry lock function does not operate for the front passenger door only, but the entry unlock function operates, the request code is being transmitted properly from the for passenger door. In this case, there may be a problem related to the lock sensor (connection between the certification ECU [smart key ECU assembly] and front door outside handle assembly [for front passenger door]).

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Front Passenger Side Door Entry Lock Function Does Not Operate


INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly (Click here).
  2. When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  3. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  4. Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) (Click here).
  5. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
1.CHECK POWER DOOR LOCK CONTROL SYSTEM

  1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.


NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.READ VALUE USING GTS (P-DOOR TRIGGER SWITCH)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Entry&Start / Data List.

  1. Read the Data List according to the display on the GTS.


Entry&Start
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
P-Door Trigger Switch
Front passenger door touch sensor (lock sensor) / ON or OFF
ON: Front passenger door touch sensor (lock sensor) touched
OFF: Front passenger door touch sensor (lock sensor) not touched
  1. Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
  2. Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.
HINT:
When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.
OK:
The GTS display changes correctly in response to the operation of the front door outside handle assembly (for front passenger door).


NG
Go to step 3
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE ASSEMBLY [FOR FRONT PASSENGER DOOR])
  1. *1: for LHD
  2. *2: for RHD

  1. Disconnect the E130 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the z75*1 or z76*2 front door outside handle assembly (for front passenger door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    		Condition
    		Specified Condition
    E130-2 (CLG2) - z75-6 (ANT1)
    		Always
    		Below 1 Ω
    E130-1 (CG2B) - z75-4 (ANT2)
    		Always
    		Below 1 Ω
    E130-2 (CLG2) or z75-6 (ANT1) - Body ground
    		Always
    		10 kΩ or higher
    E130-1 (CG2B) or z75-4 (ANT2) - Body ground
    		Always
    		10 kΩ or higher
    for RHD:
    Tester Connection
    		Condition
    		Specified Condition
    E130-2 (CLG2) - z76-6 (ANT1)
    		Always
    		Below 1 Ω
    E130-1 (CG2B) - z76-4 (ANT2)
    		Always
    		Below 1 Ω
    E130-2 (CLG2) or z76-6 (ANT1) - Body ground
    		Always
    		10 kΩ or higher
    E130-1 (CG2B) or z76-4 (ANT2) - Body ground
    		Always
    		10 kΩ or higher

  1. Reconnect the z75*1 or z76*2 front door outside handle assembly (for front passenger door) connector.

  1. Reconnect the E130 certification ECU (smart key ECU assembly) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (INPUT TO FRONT PASSENGER DOOR LOCK SENSOR)

Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Front Passenger Side Door Entry Lock Function Does Not Operate


Text in Illustration
*a
Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b
Waveform 1
*c
Lock sensor not touched
*d
Lock sensor touched

  1. Using an oscilloscope, check the waveform.

    OK:

    Tester Connection
    		Switch Condition
    		Tool Setting
    		Specified Condition
    E130-2 (CLG2) - E130-11 (E)
    		Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*)
    5. Front passenger door lock sensor touched
    		5 V/DIV., 40 ms/DIV.
    		Pulse generation (See waveform 1)
    1. *: For details about the entry function detection area, refer to Operation Check (Click here).


NG
REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)