Entry And Start System (For Entry Function) Customize Parameters

Customizing with the GTS

1. Connect the GTS to the DLC3.
   

2. Turn the engine switch on (IG).
   

3. Turn the GTS on.
   

4. Enter the following menus: Customize Setting / Wireless Door Lock, Smart Key / Access or Warning.
   

5. Select the setting by referring to the table below.
   
   

   Wireless Door Lock

   Display	Default	Content	Setting	Relevant ECU
   Wireless Control	ON	Function that turns the wireless door lock control system on or off.	OFF or ON	Main body ECU (Multiplex network body ECU)
   Hazard Answer Back	ON	When the doors are locked by the entry lock function, the hazard warning lights flash once. When the doors are unlocked by the entry lock function, the hazard warning lights flash twice.	OFF or ON	Main body ECU (Multiplex network body ECU)
   Open Door Warning*1	ON	The buzzer sounds when the lock sensor on the door outside handle assembly is touched to perform entry lock with a door open.	OFF or ON	Main body ECU (Multiplex network body ECU)
   Auto Lock Time	30 s	Function that regulates the interval between unlocking and automatic relocking of doors.	30 s, 60 s or 120 s	Main body ECU (Multiplex network body ECU)
   Wireless Buzzer Resp*2	ON	Wireless buzzer response.	OFF or ON	Main body ECU (Multiplex network body ECU)
   Wireless Buzzer Vol*2	Level5	Buzzer answer-back volume.	Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level0	Main body ECU (Multiplex network body ECU)

   1. *1: w/ Door Ajar Warning Buzzer Function
      
   2. *2: w/ Wireless Door Lock Buzzer Answer-back Function
      
   
   

   Warning

   Display	Default	Content	Setting	Relevant ECU
   Key Low Battery Warning	ON	Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more.	OFF or ON	Certification ECU (Smart key ECU assembly)

   
   

   Smart Key / Access

   Display	Default	Content	Setting	Relevant ECU
   Park Wait Time	2.5s	Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed.	0.5s, 1.5s, 2.5s or 5s	Certification ECU (Smart key ECU assembly)
   Ignition Available Area	Front or All*	Function that sets the area that the key must be in before the engine switch can be operated.	Front or All	Certification ECU (Smart key ECU assembly)
   Back Door Opening Operation	Long	Function that sets the back door when the user is carrying the electrical key transmitter sub-assembly and presses the back door opener switch assembly (open switch).	Long, Twice or OFF	Certification ECU (Smart key ECU assembly)
   Door Unlock Mode2	Driver or All*	Function that sets which doors are unlocked by the entry unlock function.	All or Driver	Certification ECU (Smart key ECU assembly)
   Auto Entry Cancel SW	OFF	Function that enables or disables the entry and start system.	OFF or ON	Certification ECU (Smart key ECU assembly)
   Touch Activation Over Threshold	Active or Not Active*	The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed.	Active or Not Active	Certification ECU (Smart key ECU assembly)
   Engine Start Indicator	ON	Function that turns the entry warning light on the combination meter assembly on or off.	OFF or ON	Certification ECU (Smart key ECU assembly)

   1. *: Default setting differs depending on the country.
      

Customizing with the multi-display

1. Turn the engine switch on (IG).
   

2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Door lock settings.
   

3. Select the setting by referring to the table below.
   
   

   Display	Default	Content	Setting	Relevant ECU
   Select Doors to Unlock	Driver's door or All doors*	Function that sets which doors are unlocked by the entry unlock function.	All Doors or Driver's Door	Certification ECU (Smart key ECU assembly)
   Entry and start system	On	Function that enables or disables the entry and start system.	On or Off	Certification ECU (Smart key ECU assembly)

   1. *: Default setting differs depending on the country.
      

Entry unlock mode switching function (manual operation)

1. The following entry unlock modes can be selected when using the entry unlock mode switching function.
   

   1. All door unlock mode: When the sensor of a front door outside handle assembly is touched, an entry unlock operation is performed simultaneously for all doors.
      
   2. Driver door unlock mode: When the sensor of the driver side door outside handle assembly is touched, an entry unlock operation is performed for the driver door only. If any other door handle is touched, an entry unlock operation is performed simultaneously for all doors.
      




2. When customizing through manual operation:
   

   1. Turn the engine switch off.
      
   2. Cancel the intrusion sensor (theft warning ultrasonic sensor).
      
   1. *: w/ Intrusion Sensor Cancel Switch
      
   3. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock switches of the electrical key transmitter sub-assembly for 5 seconds or more while the electrical key transmitter sub-assembly is in the actuation area.
      
   4. Check the current setting.
      

      HINT:

      1. The mode changes from all door unlock mode to driver door unlock mode and then back to all door unlock mode.
         
      2. The answer-back (wireless buzzer, buzzer in the combination meter assembly) operation for each mode is indicated in the table below.
         
         

         Currently Selected Mode	Answer-back (Wireless Buzzer)	Answer-back (Buzzer in Combination Meter Assembly)
         All door unlock mode	Buzzer sounds twice (short beeps)	Buzzer sounds once
         Driver door unlock mode	Buzzer sounds 3 times (short beeps)	Buzzer sounds once

   5. Release the lock and unlock switches of the electrical key transmitter sub-assembly.
      
   6. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock switches of the electrical key transmitter sub-assembly for 5 seconds or more to change the mode.
      

      HINT:

      Repeat the procedure as necessary to select the desired mode.

   7. Unlock the doors with the wireless operation, and then open any door.
      
   
   
   
   
   
   

Entry cancel function (manual operation)

HINT:

While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.

1. The following functions are disabled when the entry and start system is canceled.
   

   1. Entry unlock/lock functions
      
   2. Push-button start function
      
   3. Key lock-in prevention function
      
   4. Entry warning functions
      

2. When canceling the entry and start system through manual operation:
   

   1. Make sure the following conditions are met:
      
   1. The engine switch is off.
      
   2. The driver door is closed.
      
   3. The driver door is unlocked.
      

3. Press the unlock switch of the electrical key transmitter sub-assembly.
   

4. Open the driver door within 5 seconds of completing the step above (driver door: closed → opened).
   

5. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.
   

   NOTICE:

   If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

6. Perform the following procedure within 30 seconds of completing the step above.
   

   1. Close and open the driver door twice (driver door: open → closed → opened → closed → opened).
      
   2. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times.
      

      NOTICE:

      If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

   3. Close and open the driver door (driver door: open → closed → opened).
      

7. Close the driver door within 5 seconds (driver door: open → closed).
   

8. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.
   

9. Perform the following procedure to restore the entry and start system to the active state from the canceled state.
   

   1. Perform the procedure to cancel the entry and start system again.
      
   2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.
      

      HINT:

      1. The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.
         
      2. The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.