Front Door Lock Removal

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Door Lock. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. PRECAUTION

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

  5. REMOVE FRONT DOOR ARMREST BASE PANEL ASSEMBLY LH

  6. REMOVE DOOR ASSIST GRIP COVER LH

  7. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  8. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  9. REMOVE FRONT DOOR SERVICE HOLE COVER LH

  10. REMOVE FRONT NO. 2 DOOR STIFFENER CUSHION

  11. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

  12. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH

  13. REMOVE FRONT DOOR LOCK ASSEMBLY LH

  14. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  15. REMOVE FRONT DOOR INSIDE LOCKING LH CABLE ASSEMBLY

Front Door Lock -- Removal


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the clip and claw, and remove the front door lower frame bracket garnish LH.



4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the 7 screws and front door inside handle bezel LH.



5. REMOVE FRONT DOOR ARMREST BASE PANEL ASSEMBLY LH


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a moulding remover, detach the 5 claws.

  1. Disconnect the connector and remove the armrest base panel.



6. REMOVE DOOR ASSIST GRIP COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a moulding remover, detach the 8 claws and remove the door assist grip cover LH.



7. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the claw.

  1. Remove the courtesy light and then disconnect the connector.



8. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Door Lock.Power Door Lock Control System.Front Door Lock Removal

  1. Remove the 3 screws.

  1. Remove the 13 clips.

  1. Remove the front inner door glass weatherstrip LH together with the front door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

    HINT:
    Make sure that the pin labeled A in the illustration is detached from the door panel.

  1. Disconnect the connector.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Disconnect the 2 cables from the front door inside handle sub-assembly LH.



9. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a clip remover, detach the 9 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the front door service hole cover LH.

    HINT:
    Remove the remaining tape on the door.


10. REMOVE FRONT NO. 2 DOOR STIFFENER CUSHION


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the 2 bolts.

  1. Detach the 2 clamps and front No. 2 door stiffener cushion.



11. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the bolt and front door rear lower frame sub-assembly LH.



12. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the hole plug.

  1. Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover LH with the door lock cylinder installed.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the 2 claws and remove the front door outside handle cover LH.



13. REMOVE FRONT DOOR LOCK ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a T30 "TORX" wrench, remove the 3 screws.

    HINT:
    Remove the door lock through the service hole.
    NOTICE:
    Be careful when removing the screws as the door lock may fall and become damaged.


14. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the front door lock remote control cable assembly LH.



15. REMOVE FRONT DOOR INSIDE LOCKING LH CABLE ASSEMBLY


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Door Lock.Power Door Lock Control System.Front Door Lock Removal

  1. Using a screwdriver, detach the 3 claws.

    HINT:
    Tape the screwdriver tip before use.
    Text in Illustration
    *1
    		Protective Tape


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the front door inside locking cable assembly LH.