Dtc P0617 Starter Relay Circuit High

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - 1VD-FTV ENGINE CONTROL

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM

READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

INSPECT CLUTCH START SWITCH

REPLACE CLUTCH START SWITCH

READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)

CHECK WHETHER DTC OUTPUT RECURS

READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

INSPECT CLUTCH START SWITCH ASSEMBLY

REPLACE CLUTCH START SWITCH ASSEMBLY

INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)

CHECK WHETHER DTC OUTPUT RECURS

DTC P0617 Starter Relay Circuit High

DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.


If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.


This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) or more for more than 20 seconds.

P0617
DTC Detection Drive PatternDTC Detection ConditionTrouble Area
Drive vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or moreConditions (a), (b) and (c) are met for 20 seconds
(a) Vehicle speed is more than 20 km/h (12.4 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
Park/neutral position switch (A/T)
Starter relay circuit
Clutch start switch (M/T)
Related Data List
DTC No.Data List
P0617Starter Signal

WIRING DIAGRAM

Dtc P0617 Starter Relay Circuit High. 1VD-FTV ENGINE CONTROL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Dtc P0617 Starter Relay Circuit High. 1VD-FTV ENGINE CONTROL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

INSPECTION PROCEDURE

  • NOTICE:
  • After replacing the ECM, the new ECM needs registration () and initialization ().
  • HINT:
The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to the Problem Symptoms Table ().
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
1.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM

Check if the vehicle is equipped with the entry and start system.

Result
ResultProceed to
w/ Entry and Start SystemA
w/o Entry and Start SystemB
B
Go to step 10
A
2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON and turn the tester on.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.

Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

  • OK:
  • Ignition Switch ConditionStarter Signal
    ONOFF
    Engine startedON
Result
ResultProceed to
NG (A/T)A
NG (M/T)B
OKC
B
Go to step 5
C
CHECK FOR INTERMITTENT PROBLEMS ()
A
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Inspect the park/neutral position switch ().

Result
ResultProceed to
NGA
OKB
B
Go to step 8
A
4.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Replace the park/neutral position switch ().

NEXT
Go to step 7
5.INSPECT CLUTCH START SWITCH

Check the clutch start switch (for LHD) ().

Check the clutch start switch (for RHD) ().

Result
ResultProceed to
NGA
OKB
B
Go to step 8
A
6.REPLACE CLUTCH START SWITCH

Replace the clutch start switch (for LHD) ().

Replace the clutch start switch (for RHD) ().

NEXT
7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON and turn the tester on.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.

Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

  • OK:
  • Ignition Switch ConditionStarter Signal
    ONOFF
    Engine startedON
Result
ResultProceed to
NGA
OKB
B
SYSTEM OK
A
8.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)
NG
REPLACE HARNESS OR CONNECTOR
OK
9.CHECK WHETHER DTC OUTPUT RECURS

Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON.

Turn the tester on.

Clear the DTCs ().

Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more.

Enter the following menus: Powertrain / Engine / DTC.

Read the DTCs.

Result
Display (DTC Output)Proceed to
P0617A
No outputB
B
SYSTEM OK
A
GO TO CRANKING HOLDING FUNCTION CIRCUIT ()
10.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON and turn the tester on.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.

Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

  • OK:
  • Ignition Switch ConditionStarter Signal
    ONOFF
    Engine startedON
Result
ResultProceed to
NG (A/T)A
NG (M/T)B
OKC
B
Go to step 13
C
CHECK FOR INTERMITTENT PROBLEMS ()
A
11.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Inspect the park/neutral position switch ().

Result
ResultProceed to
NGA
OKB
B
Go to step 15
A
12.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Replace the park/neutral position switch ().

NEXT
Go to step 17
13.INSPECT CLUTCH START SWITCH ASSEMBLY

Check the clutch start switch (for LHD) ().

Check the clutch start switch (for RHD) ().

Result
ResultProceed to
NGA
OKB
B
Go to step 15
A
14.REPLACE CLUTCH START SWITCH ASSEMBLY

Replace the clutch start switch (for LHD) ().

Replace the clutch start switch (for RHD) ().

NEXT
Go to step 17
15.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

Inspect the Ignition or Starter Switch Assembly ().

Result
ResultProceed to
NGA
OKB
B
Go to step 18
A
16.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

Replace the Ignition or Starter Switch Assembly ().

NEXT
17.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON and turn the tester on.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.

Check the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

  • OK:
  • Ignition Switch ConditionStarter Signal
    ONOFF
    Engine startedON
Result
ResultProceed to
NGA
OKB
B
SYSTEM OK
A
18.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)
NG
REPLACE HARNESS OR CONNECTOR
OK
19.CHECK WHETHER DTC OUTPUT RECURS

Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON.

Turn the tester on.

Clear the DTCs ().

Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more.

Enter the following menus: Powertrain / Engine / DTC.

Read the DTCs.

Result
Display (DTC Output)Proceed to
P0617A
No outputB
B
SYSTEM OK
A
REPLACE ECM ()