Dtc B15D8 Monitor Disconnected

Audio Visual Telematics. Land Cruiser. Urj200, 202 Grj200 Vdj200
Navigation Multi Info Display. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CLEAR DTC

CHECK DTC

CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)

INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY

CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - PARKING ASSIST ECU)

REPLACE PARKING ASSIST ECU

CLEAR DTC

CHECK DTC

DTC B15D8 Monitor Disconnected


DESCRIPTION

The parking assist ECU and multi-media module receiver assembly are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the multi-media module receiver assembly and parking assist ECU, these DTCs will be stored.

DTC Code
DTC Detection Condition
Trouble Area
B15D8*
A device that is listed in the AVC-LAN connected device record of the master unit is missing.
  1. Parking assist ECU power source circuit
  2. AVC-LAN circuit
  3. Parking assist ECU
  4. Multi-media module receiver assembly
HINT:
  1. *: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The multi-media module receiver assembly is the master unit.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Navigation Multi Info Display.Navigation System. Dtc B15D8 Monitor Disconnected


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
1.CLEAR DTC

  1. Clear the DTCs (Click here).


NEXT


2.CHECK DTC

  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output


NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Navigation Multi Info Display.Navigation System. Dtc B15D8 Monitor Disconnected

  1. Disconnect the parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    F75-4 (GND1) - Body ground
    		Always
    		Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    F75-1 (+B) - F75-4 (GND1)
    		Always
    		11 to 14 V
    F75-8 (IG) - F75-4 (GND1)
    		Engine switch on (IG)
    		11 to 14 V
    F75-9 (ACC) - F75-4 (GND1)
    		Engine switch on (ACC)
    		11 to 14 V
Text in Illustration
*a
Front view of wire harness connector
(to Parking Assist ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Navigation Multi Info Display.Navigation System. Dtc B15D8 Monitor Disconnected

  1. Remove the multi-media module receiver assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    7 (TX1+) - 8 (TX1-)
    		Always
    		60 to 80 Ω


NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - PARKING ASSIST ECU)

  1. Disconnect the F77 multi-media module receiver assembly connector.

  1. Disconnect the F75 parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    F77-7 (TX1+) - F75-11 (TX+)
    		Always
    		Below 1 Ω
    F77-8 (TX1-) - F75-10 (TX-)
    		Always
    		Below 1 Ω
    F77-7 (TX1+) - Body ground
    		Always
    		10 kΩ or higher
    F77-8 (TX1-) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE PARKING ASSIST ECU

  1. Replace the parking assist ECU with a new or normally functioning one (Click here).


NEXT


7.CLEAR DTC

  1. Clear the DTCs (Click here).


NEXT


8.CHECK DTC

  1. Recheck for DTCs and check if the same DTC is output again (Click here).



NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK

END (PARKING ASSIST ECU IS DEFECTIVE)