Variable Gear Ratio Steering System Test Mode Procedure

Steering. Land Cruiser. Urj200, 202 Grj200 Vdj200
Variable Gear Ratio Steering. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. TEST MODE (VGRS SENSOR SIGNAL CHECK)

  1. TEST MODE DTC

Variable Gear Ratio Steering System -- Test Mode Procedure



TEST MODE (VGRS SENSOR SIGNAL CHECK)
HINT:

  1. Land Cruiser. Urj200, 202 Grj200 Vdj200
    When the system enters test mode, "VGRS Test Mode" is displayed on the multi-information display.
  2. Before entering test mode, check and repair any malfunctions indicated by the present DTCs of the VGRS system.
  3. By switching from normal mode to test mode, the steering angle sensor can be read.
  4. When entering test mode, the steering control ECU sets all the test mode DTCs first.
  5. When the mode is switched from test mode to normal mode, all the test mode DTCs will be cleared.

  1. Check the test mode DTCs (using the tester).

    1. Turn the engine switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the engine switch on (IG) and turn the tester on.

    4. Read the test mode DTCs by following the prompts on the tester screen.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  2. Clear the test mode DTCs (using the tester).

    1. Turn the engine switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the engine switch on (IG) and turn the tester on.

    4. Switch the system from test mode to normal mode by following the directions on the tester screen.

      HINT:
      Refer to the intelligent tester operator's manual for further details.


  3. Check the test mode DTCs (using SST check wire).

    NOTICE:
    Perform these procedures with the vehicle stopped.

    1. Turn the engine switch off.



      2. Land Cruiser. Urj200, 202 Grj200 Vdj200.Variable Gear Ratio Steering.Variable Gear Ratio Steering System.Variable Gear Ratio Steering System Test Mode Procedure

    2. Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

      SST
      09843-18040

    3. Turn the engine switch on (IG).

    4. Read 2-digit test mode DTCs from the multi-information display.

  4. Clear the test mode DTCs (using SST check wire).

    1. Turn the engine switch off.

    2. Disconnect SST from the DLC3.

      SST
      09843-18040

    3. Turn the engine switch on (IG).

      HINT:
      If the engine switch is turned on (IG) with terminals 12 (TS) and 4 (CG) connected, the system remains in test mode.

TEST MODE DTC

  1. If a trouble code is displayed during the DTC check, check the circuit indicated by the DTC. For details of each code, proceed to the DTC chart.

    DTC Code
    		Detection Item
    		Trouble Area
    		Proceed to
    C15C4/68
    		A steering signal indicating a tire angle of 36° or more (to the left or right) is input after entering test mode*
    1. Steering angle sensor
    2. Harness or connector
    3. Steering control ECU
    		Click here
    C15C5/69
    		A steering signal indicating a motor rotation angle of 36° or more (to the left or right) is input after entering test mode*
    1. Harness or connector
    2. Steering actuator
    3. Steering control ECU
    		Click here
    HINT:
    *: A tire angle of 36° and a motor rotation angle of 36° correspond to the steering wheel angle. The amount of change in tire angle and motor rotation angle is from when the mode is changed to test mode.