Dtc C1210 Zero Point Calibration Of Yaw Rate Sensor Undone

Brake. Land Cruiser. Urj200, 202 Grj200 Vdj200
Brake Control Dynamic Control Systems. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

INSPECTION PROCEDURE

CHECK DTC (CAN COMMUNICATION SYSTEM)

PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR

PERFORM TEST MODE (SIGNAL CHECK)

CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)

DTC C1210 Zero Point Calibration of Yaw Rate Sensor Undone

DTC C1336 Zero Point Calibration of Acceleration Sensor Undone


DESCRIPTION

The skid control ECU (master cylinder solenoid) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.
The yaw rate and acceleration sensor has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U0124 (acceleration sensor communication trouble) are stored.
The DTCs are also stored when the calibration has not been completed.

DTC Code
DTC Detection Condition
Trouble Area
C1210
Zero point calibration of the yaw rate sensor is incomplete.
  1. Zero point calibration incomplete
  2. Sensor installation
  3. Yaw rate and acceleration sensor (Airbag sensor assembly)
  4. Skid control ECU (Master cylinder solenoid)
C1336
Zero point calibration of the acceleration sensor is incomplete.

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the master cylinder solenoid, perform zero point calibration and store the system information (Click here).
  2. After replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration (Click here).
1.CHECK DTC (CAN COMMUNICATION SYSTEM)

  1. for LHD (with Central Gateway ECU):
    Check for DTCs (Click here).

  1. for LHD (without Central Gateway ECU):
    Check for DTCs (Click here).

  1. for RHD (with Central Gateway ECU):
    Check for DTCs (Click here).

  1. for RHD (without Central Gateway ECU):
    Check for DTCs (Click here).

    Result
    Result
    		Proceed to
    CAN DTC is not output
    		A
    CAN DTC is output (for LHD (with Central Gateway ECU))
    		B
    CAN DTC is output (for LHD (without Central Gateway ECU))
    		C
    CAN DTC is output (for RHD (with Central Gateway ECU))
    		D
    CAN DTC is output (for RHD (without Central Gateway ECU))
    		E



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

E
GO TO CAN COMMUNICATION SYSTEM ( HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR

  1. Perform zero point calibration of the yaw rate and acceleration sensor (Click here).


NEXT


3.PERFORM TEST MODE (SIGNAL CHECK)

  1. Turn the ignition switch off.

  1. Perform the signal check in the Test Mode Procedure (Click here).

    OK:
    All test mode DTCs are cleared.


NG
Go to step 4
OK

END

4.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

  1. Turn the ignition switch off.

  1. Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly (Click here).

    OK:
    The sensor is tightened to the specified torque.
    The sensor is not installed at an angle.


NG
INSTALL AIRBAG SENSOR ASSEMBLY (Click here)
OK


5.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)

  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Deceleration Sensor
    		Acceleration sensor reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2
    		-
    		Changes continuously during acceleration/deceleration.
    Deceleration Sensor2
    		Acceleration sensor 2 reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2
    		-
    		Changes continuously during acceleration/deceleration.
    Yaw Rate Sensor
    		Yaw rate sensor/ Min.: -128°/s, Max.: 127°/s
    		Vehicle stationary: 0°/s
    Right turn: -128 to 0°/s
    Left turn: 0 to 127°/s
    		-

  1. Check that the yaw rate and acceleration sensor output value is displayed on the GTS.

    OK:
    The yaw rate and acceleration sensor output value is normal.

Result
Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C


B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)