Automatic Transmission Fluid Adjustment

Using compressed air or equivalent, blow dust off the thermostat cap to clean it.

Using a screwdriver, push in the shaft of the thermostat.

HINT:

1. Pushed amount: 5.5 to 7.0 mm (0.217 to 0.276 in.)
   
2. Push in the shaft until the screwdriver contacts the step inside the cap.
   

With the shaft of the thermostat pressed, insert a pin into a hole on the side of the thermostat cap. Insert the pin until it passes through the hole on the other side of the thermostat cap to fix the shaft in place.

HINT:

Pin diameter: 1.0 to 1.8 mm (0.0394 to 0.0709 in.)

Remove the refill plug and overflow plug.

Fill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.

Reinstall the overflow plug.

Fill the transmission with the amount of fluid listed in the table below.

Standard Capacity:

Repair	Fill Amount
Transmission pan and drain plug removal	2.1 liters (2.2 US qts, 1.9 Imp. qts)
Transmission valve body removal	4.7 liters (5.0 US qts, 4.1 Imp. qts)
Torque converter removal	6.1 liters (6.4 US qts, 5.4 Imp. qts)

Reinstall the refill plug to prevent the fluid from splashing.

HINT:

If you cannot add the listed amount of fluid, do the following:

1. Install the refill plug.
   

2. Allow the engine to idle with the air conditioning OFF.
   

3. Move the shift lever through the entire gear range to circulate fluid.
   

4. Wait for 30 seconds with the engine idling.
   

5. Stop the engine.
   

6. Remove the refill plug and add fluid.
   

7. Reinstall the refill plug.
   

When using the GTS:

1. Turn the ignition switch off.
   

2. Connect the GTS to the DLC3.
   

3. Turn the ignition switch to ON.
   

4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
   

5. Enter the following menus: Powertrain / Engine and ECT / Data List / A/T Oil Temperature 1.
   

6. for 1VD-FTV:
   Check the ATF temperature.
   

   NOTICE:

   1. The ATF temperature must be between 41 to 46°C (106 to 115°F).
      
   2. If the ATF temperature is not between 41 to 46°C (106 to 115°F), turn the ignition switch off and wait until the fluid temperature drops between 41 to 46°C (106 to 115°F).
      

7. for 1UR-FE:
   Check the ATF temperature.
   

   NOTICE:

   1. The ATF temperature must be between 43 to 48°C (109 to 118°F).
      
   2. If the ATF temperature is not between 43 to 48°C (109 to 118°F), turn the ignition switch off and wait until the fluid temperature drops between 43 to 48°C (109 to 118°F).
      

8. for 1VD-FTV:
   According to the display on the GTS, perform the Active Test "Connect the TC and TE1".
   

9. for 1UR-FE:
   According to the display on the GTS, perform the Active Test "Connect the TC and TE1".
   

   HINT:

   Indicator lights of the combination meter blink to output DTCs when TC and TE1 are connected.

10. Start the engine.
    

    NOTICE:

    Check that electrical systems such as the air conditioning system, audio system and lighting system are off.

When not using the GTS:

1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
   

   SST

   09843-18040
   

   Text in Illustration

   *A	Front View of DLC3

2. Start the engine.
   

   NOTICE:

   Check that electrical systems such as the air conditioning system, audio system and lighting system are off.

   HINT:

   Indicator lights of the meter blink to output DTCs when terminals TC and CG are connected.

Slowly move the shift lever from P to S, then change the gears from 1st to 6th. Then return the shift lever to P.

HINT:

Slowly move the shift lever to circulate the fluid through each part of the transmission.

Move the shift lever to D, and quickly move back and forth between N and D (once within 1.5 seconds) for at least 6 seconds. This will activate the fluid temperature detection mode.

Standard condition:

Indicator light (D) remains illuminated for 2 seconds and then turns off.

When using the GTS:

1. Return the shift lever to P and press OFF on the Active Test display.
   

When not using the GTS:

1. Return the shift lever to P and disconnect terminals 13 (TC) and 4 (CG).
   

for 1VD-FTV:
Allow the engine to idle until the fluid temperature reaches 41 to 46°C (106 to 115°F).

for 1UR-FE:
Allow the engine to idle until the fluid temperature reaches 43 to 48°C (109 to 118°F).

for 1VD-FTV:
The indicator (D) will come on again when the fluid temperature reaches 41°C (106°F) and will blink when it exceeds 46°C (115°F).

Indicator Indication of ATF Temperature :

Below Proper Temperature	Proper Temperature	Higher than Proper Temperature
Data List [A/T Oil Temperature 1] 41°C (106°F) or less	Data List [A/T Oil Temperature 1] 41 to 46°C (106 to 115°F)	Data List [A/T Oil Temperature 1] 46°C (115°F) or higher
Indicator light (D) Turns off	Indicator light (D) Turns on	Indicator light (D) Blinking

NOTICE:

Perform the fluid level inspection while the indicator light is on.

for 1UR-FE:
The indicator (D) will come on again when the fluid temperature reaches 43°C (109°F) and will blink when it exceeds 48°C (118°F).

Indicator Indication of ATF Temperature :

Below Proper Temperature	Proper Temperature	Higher than Proper Temperature
Data List [A/T Oil Temperature 1] 43°C (109°F) or less	Data List [A/T Oil Temperature 1] 43 to 48°C (109 to 118°F)	Data List [A/T Oil Temperature 1] 48°C (118°F) or higher
Indicator light (D) Turns off	Indicator light (D) Turns on	Indicator light (D) Blinking

NOTICE:

Perform the fluid level inspection while the indicator light is on.

Remove the overflow plug with the engine idling.

Check that fluid comes out of the overflow tube.
If fluid does not come out, proceed to the "Transmission Refill" procedures.
If fluid comes out, wait until the overflow slows to a trickle and proceed to the "Complete" procedures.

Remove the overflow plug.

Remove the refill plug and gasket.

Add ATF into the refill hole until ATF flows from the overflow tube.

Wait until the overflow slows to a trickle and proceed to the "Complete" procedures.

Install a new gasket and the overflow plug.

Torque:

20 N*m{204 kgf*cm, 15 ft.*lbf}

Stop the engine.

Install a new gasket and the refill plug.

Torque:

39 N*m{400 kgf*cm, 29 ft.*lbf}