Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

Drivetrain. Land Cruiser. Urj200, 202 Grj200 Vdj200
Ab60F Automatic Transmission Transaxle. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

INSPECT TRANSMISSION CONTROL SWITCH

CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)

CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)

CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.

DTC Code
DTC Detection Condition
Trouble Area
P0705
When one of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic).
  1. P input signal
  2. N input signal
  3. R input signal
  4. D input signal
(B) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic).
  1. NSW input signal
  2. R input signal
  3. D input signal
(C) Any of the following signals are ON for 2.0 sec. or more when the shift lever is in S (2 trip detection logic).
  1. NSW input signal
  2. P input signal
  3. N input signal
  4. R input signal
(D) All the signals are OFF simultaneously for the P, R, N and D positions (2 trip detection logic).
  1. Park/neutral position switch
  2. Transmission control switch (Lower shift lever assembly)
  3. Open or short in park/neutral position switch circuit
  4. ECM

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or S).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)


Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)


INSPECTION PROCEDURE


DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the tester, read the Data List.

    ECT
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Neutral Position SW Signal
    		PNP switch status/
    ON or OFF
    		Shift lever:
    1. In P or N: ON
    2. Not in P or N: OFF
    		When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (R Range)
    		PNP switch status/
    ON or OFF
    		Shift lever:
    1. In R: ON
    2. Not in R: OFF
    		When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (P Range)
    		PNP switch status/
    ON or OFF
    		Shift lever:
    1. In P: ON
    2. Not in P: OFF
    		When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (N Range)
    		PNP switch status/
    ON or OFF
    		Shift lever:
    1. In N: ON
    2. Not in N: OFF
    		When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (D Range)
    		PNP switch status/
    ON or OFF
    		Shift lever:
    1. In D: ON
    2. Not in D: OFF
    		When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Sports Shift Up SW
    		Sport shift up switch status/
    ON or OFF
    1. ON: Shift lever held in "+" (up-shift)
    2. OFF: Shift lever not in "+" (up-shift)
    		-
    Sports Shift Down SW
    		Sport shift down switch status/
    ON or OFF
    1. ON: Shift lever held in "-" (down-shift)
    2. OFF: Shift lever not in "-" (down-shift)
    		-
1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    1. 2 (RB) - 6 (PL)
    2. 4 (B) - 5 (L)
    		Shift lever in P
    		Below 1 Ω
    2 (RB) - 1 (RL)
    		Shift lever in R
    		Below 1 Ω
    1. 2 (RB) - 9 (NL)
    2. 4 (B) - 5 (L)
    		Shift lever in N
    		Below 1 Ω
    2 (RB) - 7 (DL)
    1. Shift lever in D
    2. Shift lever in S, "+" or "-"
    		Below 1 Ω
    1. 2 (RB) - 6 (PL)
    2. 4 (B) - 5 (L)
    		Shift lever not in P
    		10 kΩ or higher
    2 (RB) - 1 (RL)
    		Shift lever not in R
    		10 kΩ or higher
    1. 2 (RB) - 9 (NL)
    2. 4 (B) - 5 (L)
    		Shift lever not in N
    		10 kΩ or higher
    2 (RB) - 7 (DL)
    1. Shift lever not in D
    2. Shift lever not in S, "+" or "-"
    		10 kΩ or higher


NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


2.INSPECT TRANSMISSION CONTROL SWITCH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

  1. Disconnect the transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    3 (IG) - 7 (S)
    		Shift lever in S, "+" or "-"
    		Below 1 Ω
    3 (IG) - 7 (S)
    		Shift lever not in S, "+" or "-"
    		10 kΩ or higher


NG
REPLACE TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY) (Click here)
OK


3.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

  1. Disconnect the park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    C24-2 (RB) - Body ground
    		Ignition switch ON
    		11 to 14 V
    C24-2 (RB) - Body ground
    		Ignition switch off
    		Below 1 V


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BK/UK LP FUSE)
OK


4.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

  1. Disconnect the transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    E52-3 (IG) - Body ground
    		Ignition switch ON
    		11 to 14 V
    E52-3 (IG) - Body ground
    		Ignition switch off
    		Below 1 V


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - LH-IG FUSE)
OK


5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD
    Tester Connection
    		Condition
    		Specified Condition
    1. C45-31 (P) - Body ground
    2. A38-43 (NSW) - Body ground
    1. Ignition switch ON
    2. Shift lever in P
    		11 to 14 V
    C45-30 (R) - Body ground
    1. Ignition switch ON
    2. Shift lever in R
    		11 to 14 V*
    1. C45-29 (N) - Body ground
    2. A38-43 (NSW) - Body ground
    1. Ignition switch ON
    2. Shift lever in N
    		11 to 14 V
    C45-28 (D) - Body ground
    1. Ignition switch ON
    2. Shift lever in D
    		11 to 14 V
    1. C45-31 (P) - Body ground
    2. A38-43 (NSW) - Body ground
    1. Ignition switch ON
    2. Shift lever not in P
    		Below 1 V
    C45-30 (R) - Body ground
    1. Ignition switch ON
    2. Shift lever not in R
    		Below 1 V
    1. C45-29 (N) - Body ground
    2. A38-43 (NSW) - Body ground
    1. Ignition switch ON
    2. Shift lever not in N
    		Below 1 V
    C45-28 (D) - Body ground
    1. Ignition switch ON
    2. Shift lever not in D
    		Below 1 V
    for RHD
    Tester Connection
    		Condition
    		Specified Condition
    1. C46-31 (P) - Body ground
    2. A52-43 (NSW) - Body ground
    1. Ignition switch ON
    2. Shift lever in P
    		11 to 14 V
    C46-30 (R) - Body ground
    1. Ignition switch ON
    2. Shift lever in R
    		11 to 14 V*
    1. C46-29 (N) - Body ground
    2. A52-43 (NSW) - Body ground
    1. Ignition switch ON
    2. Shift lever in N
    		11 to 14 V
    C46-28 (D) - Body ground
    1. Ignition switch ON
    2. Shift lever in D
    		11 to 14 V
    1. C46-31 (P) - Body ground
    2. A52-43 (NSW) - Body ground
    1. Ignition switch ON
    2. Shift lever not in P
    		Below 1 V
    C46-30 (R) - Body ground
    1. Ignition switch ON
    2. Shift lever not in R
    		Below 1 V
    1. C46-29 (N) - Body ground
    2. A52-43 (NSW) - Body ground
    1. Ignition switch ON
    2. Shift lever not in N
    		Below 1 V
    C46-28 (D) - Body ground
    1. Ignition switch ON
    2. Shift lever not in D
    		Below 1 V
    HINT:
    *: The voltage will drop slightly due to the turning on of the back up light.


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD
    Tester Connection
    		Condition
    		Specified Condition
    A38-25 (S) - Body ground
    		Shift lever in S, "+" or "-"
    		11 to 14 V
    A38-25 (S) - Body ground
    		Shift lever not in S, "+" or "-"
    		Below 1 V
    for RHD
    Tester Connection
    		Condition
    		Specified Condition
    A52-25 (S) - Body ground
    		Shift lever in S, "+" or "-"
    		11 to 14 V
    A52-25 (S) - Body ground
    		Shift lever not in S, "+" or "-"
    		Below 1 V


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)