Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - 1UR-FE ENGINE CONTROL

The intake camshaft has 3 teeth on its outer circumference. When the intake camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE fluctuates. The VVT sensor converts the camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends the data to the ECM.

The crankshaft angle sensor rotor has 34 teeth. The MRE generates 34 signals for each crankshaft revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC No.	DTC Detection Condition	Trouble Area
P0340 P0345	No VVT sensor signal is sent to the ECM at an engine speed of 600 rpm or more (1 trip detection logic).	Open or short in VVT sensor circuit for intake camshaft VVT sensor for intake camshaft Intake camshaft Timing chain for intake camshaft jumped tooth ECM
P0342 P0347	Output voltage of VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).	Open or short in VVT sensor circuit for intake camshaft VVT sensor for intake camshaft Intake camshaft Timing chain for intake camshaft jumped tooth ECM
P0343 P0348	Output voltage of VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).	Open or short in VVT sensor circuit for intake camshaft VVT sensor for intake camshaft Intake camshaft Timing chain for intake camshaft jumped tooth ECM

Dtc P0340 Camshaft Position Sensor Circuit Malfunction. 1UR-FE ENGINE CONTROL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Reference: Inspection using an oscilloscope

Standard:

for RHD
Tester Connection	Tool Setting	Condition	Specified Condition
C46-110 (NE+) - C46-111 (NE-)	5 V/DIV. 20 msec./DIV.	Cranking or idling	The correct waveform is as shown
C46-92 (VV1+) - C46-91 (VV1-)	5 V/DIV. 20 msec./DIV.	Cranking or idling	The correct waveform is as shown
C46-87 (VV2+) - C46-88 (VV2-)	5 V/DIV. 20 msec./DIV.	Cranking or idling	The correct waveform is as shown

for LHD
Tester Connection	Tool Setting	Condition	Specified Condition
C45-110 (NE+) - C45-111 (NE-)	5 V/DIV. 20 msec./DIV.	Cranking or idling	The correct waveform is as shown
C45-92 (VV1+) - C45-91 (VV1-)	5 V/DIV. 20 msec./DIV.	Cranking or idling	The correct waveform is as shown
C45-87 (VV2+) - C45-88 (VV2-)	5 V/DIV. 20 msec./DIV.	Cranking or idling	The correct waveform is as shown

HINT:

VV1 and VV2 are the VVT sensor signals, and NE is the crankshaft position sensor signal.

MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine running, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at below 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

Start the engine and run it at idle for 10 seconds or more.

WIRING DIAGRAM

Dtc P0340 Camshaft Position Sensor Circuit Malfunction. 1UR-FE ENGINE CONTROL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

INSPECTION PROCEDURE

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)

Disconnect the VVT sensor connector.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.0 V

Text in Illustration
*a	Front view of wire harness connector (to VVT Sensor)
*b	Bank 1
*c	Bank 2

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM)

Disconnect the VVT sensor connector.

Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for RHD
Tester Connection	Condition	Specified Condition
C100-1 (VVL+) - C46-92 (VV1+)	Always	Below 1 Ω
C100-2 (VVL-) - C46-91 (VV1-)	Always	Below 1 Ω
C101-1 (VVR+) - C46-87 (VV2+)	Always	Below 1 Ω
C101-2 (VVR-) - C46-88 (VV2-)	Always	Below 1 Ω
C100-1 (VVL+) or C46-92 (VV1+) - Body ground	Always	10 kΩ or higher
C100-2 (VVL-) or C46-91 (VV1-) - Body ground	Always	10 kΩ or higher
C101-1 (VVR+) or C46-87 (VV2+) - Body ground	Always	10 kΩ or higher
C101-2 (VVR-) or C46-88 (VV2-) - Body ground	Always	10 kΩ or higher

for LHD
Tester Connection	Condition	Specified Condition
C100-1 (VVL+) - C45-92 (VV1+)	Always	Below 1 Ω
C100-2 (VVL-) - C45-91 (VV1-)	Always	Below 1 Ω
C101-1 (VVR+) - C45-87 (VV2+)	Always	Below 1 Ω
C101-2 (VVR-) - C45-88 (VV2-)	Always	Below 1 Ω
C100-1 (VVL+) or C45-92 (VV1+) - Body ground	Always	10 kΩ or higher
C100-2 (VVL-) or C45-91 (VV1-) - Body ground	Always	10 kΩ or higher
C101-1 (VVR+) or C45-87 (VV2+) - Body ground	Always	10 kΩ or higher
C101-2 (VVR-) or C45-88 (VV2-) - Body ground	Always	10 kΩ or higher

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT)

Check the VVT sensor installation.

OK:
Sensor is installed correctly.

SECURELY REINSTALL SENSOR ()

OK

4.INSPECT INTAKE CAMSHAFT (TEETH)

Check the teeth of the camshaft.

OK:
Teeth do not have any cracks or deformation.

REPLACE INTAKE CAMSHAFT ()

OK

5.REPLACE VVT SENSOR

Replace the VVT sensor ().

NEXT

6.CHECK WHETHER DTC OUTPUT RECURS

Connect the GTS to the DLC3.

Turn the engine switch on (IG).

Turn the GTS on.

Clear DTCs.

Start the engine and idle it for 10 seconds or more.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

Read DTCs.

Result
Result	Proceed to
No DTC is output	A
P0340, P0342, P0343, P0345, P0347 or P0348 is output	B

HINT:

If the engine does not start, replace the ECM.

REPLACE ECM ()

END

Tester Connection	Switch Condition	Specified Condition
3 (VC) - Body ground	Engine switch on (IG)	4.5 to 5.0 V