Engine Hybrid System. Land Cruiser. Urj200, 202 Grj200 Vdj200
Cruise Control. Land Cruiser. Urj200, 202 Grj200 Vdj200
Dynamic Radar Cruise Control System -- Data List / Active Test |
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Radar Cruise / Data List.
According to the display on the intelligent tester , read the "Data List".
Radar Cruise Tester Display Measurement Item/Range Normal Condition Diagnostic Note Accel Request Accelerator request signal / min.: -2621.44 km/h/s, max.: 2621.36 km/h/s Actual demanded acceleration request - Vehicle Distance Millimeter wave radar sensor / min.: 0 m (0 ft.), max.: 255 m (836.65 ft.) Distance to the vehicle in front - L/C Option Flag Dynamic radar cruise option flag / NO or YES YES: Vehicle-to-vehicle distance control mode is selectable
NO: Vehicle-to-vehicle distance control mode is not selectable- Car Dist Time Setting Vehicle distance time setting condition / SHORT, MID, LONG or NO Vehicle distance selected by steering pad switch (distance control switch) - O/D Cut Request O/D cut request / Not Request or Request Not Request: Idling
Request: Performed- Shift Down Rqst to 3rd Shift down request to 3rd gear / Not Request or Request Not Request: Idling
Request: Performed- Shift Down Rqst to 4th Shift down request to 4th gear / Not Request or Request Not Request: Idling
Request: Performed- Alarm Request Alarm request signal / Not Request or Request Request: When beeping
Not Request: When not beeping- All Throttle Close Rqst All throttle close request / Not Request or Request Request: Requested
Not Request: Not requested- Brake Control Request Brake control request / Not Request or Request Request: Requested
Not Request: Not requested- Targ Decl Slope Cruise target deceleration slope / 0, 1, 2 or 3 0, 1, 2 or 3 - CCS Vehicle Spd Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph) Actual vehicle speed displayed - CCS Mem Vehicle Spd Vehicle speed / min.: 0 km/h (0 mph), max.: 200 km/h (125 mph) Actual vehicle speed stored in memory - Cruise Operation Status Transmission range sensor signal / ON or OFF ON: Shift lever in D (6th, 5th or 4th gear)
OFF: Shift lever not in D (6th, 5th or 4th gear)- Cruise Control Cruise control / ON or OFF ON: Cruise control operating
OFF: Cruise control not operating- CCS Indicator M-CPU CRUISE main indicator light (Main CPU) / ON or OFF ON: CRUISE main indicator light on
OFF: CRUISE main indicator light off- CCS Ready M-CPU Cruise control system standby condition (Main CPU) / ON or OFF ON: Cruise control main switch (Main CPU) on
OFF: Cruise control main switch (Main CPU) off- Main SW M-CPU Cruise control main switch (Main CPU) / ON or OFF ON: Cruise control main switch (Main CPU) on
OFF: Cruise control main switch (Main CPU) off- Cancel Switch CANCEL switch / ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off- SET/COAST Switch -SET switch / ON or OFF ON: -SET switch on
OFF: -SET switch off- RES/ACC Switch +RES switch / ON or OFF ON: +RES switch on
OFF: +RES switch off- Stop Light SW M-CPU Stop light switch signal (Main CPU) / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- Throttle Opening Angle Cruise throttle opening angle / min.: 0 deg, max.: 125 deg Actual demanded throttle angle - VSC Fail Safe Flag Vehicle stability control system fail-safe flag / OFF or ON ON: Vehicle stability control system fail-safe flag on
OFF: Vehicle stability control system fail-safe flag off- Brake Cancel Switch Brake cancel switch (stop light switch) signal / OFF or ON ON: Brake pedal depressed
OFF: Brake pedal released- Distance Control Switch Distance control switch signal / ON or OFF ON: Distance control switch on
OFF: Distance control switch off- # Codes Number of trouble codes / Min.: 0, Max.: 255 - -
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: All ECUs / (desired system) / Active Test.
According to the display on the intelligent tester, perform the "Active Test".
Combination Meter Tester Display Test Part Control Range Diagnostic Note Indicat. Lamp Cruise Cruise control indicator light OFF or ON - Indicat. Radar Cruise Radar cruise indicator light OFF or ON - Indicat. SET Cruise control SET indicator light OFF or ON - ABS/VSC/TRAC Tester Display Test Part Control Range Diagnostic Note Buzzer Skid control buzzer sounds OFF or ON -