Engine Oil Cooler -- Removal |
| 1. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH |
Remove the 3 bolts and screw.
 |
Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.
| 2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH |
Remove the 3 bolts and 2 screws.
 |
Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.
| 3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
Remove the 10 bolts and No. 1 engine under cover.
 |
| 4. DRAIN ENGINE COOLANT |
- CAUTION:
- Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
| *1 | Radiator Reservoir | *2 | Radiator Cap |
| *3 | Radiator Drain Cock Plug | *4 | Cylinder Block Water Drain Cock Plug |
| *a | for Type A | *b | for Type B |
for Type A:
Loosen the radiator drain cock plug and 2 cylinder block water drain cock plugs.
for Type B:
Loosen the radiator drain cock plug and cylinder block water drain cock plug.
Remove the radiator cap. Then drain the coolant.
- HINT:
- Collect the coolant in a container and dispose of it according to the regulations in your area.
for Type A:
Tighten the 2 cylinder block water drain cock plugs.- Torque:
- 13 N*m{130 kgf*cm, 9 ft.*lbf}
for Type B:
Tighten the cylinder block water drain cock plug.- Torque:
- 13 N*m{130 kgf*cm, 9 ft.*lbf}
Tighten the radiator drain cock plug by hand.
| 5. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the 2 bolts and No. 2 engine under cover seal.
Remove the oil pan drain plug and gasket, and drain the engine oil into a container.
Install a new gasket and the oil pan drain plug.
- Torque:
- 40 N*m{408 kgf*cm, 30 ft.*lbf}
Install the No. 2 engine under cover seal with the 2 bolts.
- Torque:
- 10 N*m{102 kgf*cm, 7 ft.*lbf}
| 6. REMOVE OIL FILTER ELEMENT |
Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
Text in Illustration *1 Pipe *2 Hose
 |
Remove the oil filter drain plug.
 |
Install the pipe to the oil filter cap.
Text in Illustration *1 Cap *2 Valve *3 Pipe *4 O-Ring *5 Hose - NOTICE:
- If the O-ring is removed with the drain plug, install the O-ring together with the pipe.
- HINT:
- Use a container to catch the draining oil.
 |
Check that oil is drained from the oil filter. Then, disconnect the pipe and remove the O-ring as shown in the illustration.
 |
Using SST, remove the oil filter cap.
- SST
- 09228-06501
Text in Illustration *1 Oil Filter Bracket Clip - NOTICE:
- Do not remove the oil filter bracket clip.
 |
Remove the oil filter element and O-ring from the oil filter cap.
Text in Illustration *1 O-Ring - NOTICE:
- Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.
 |
| 7. DISCONNECT WATER BY-PASS PIPE SUB-ASSEMBLY |
Remove the 3 bolts.
 |
Disconnect the 2 hoses and water by-pass pipe.
 |
| 8. REMOVE OIL FILTER BRACKET |
Remove the 2 nuts, bolt, oil filter bracket and gasket.
 |
| 9. REMOVE OIL COOLER ASSEMBLY |
Remove the 2 hoses.
 |
Remove the bolt, nut and oil cooler.
 |
Remove the seal washer from the bolt.