INSTALL REAR NO. 7 AIR DUCT (w/ Rear Air Conditioning System)
INSTALL REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System)
INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)
INSTALL REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side)
INSTALL REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side)
Fuel Sender Gauge Assembly (For Fuel Sub Tank) -- Installation |
| 1. INSTALL FUEL SENDER GAUGE ASSEMBLY |
Install a new gasket to the fuel sender gauge assembly.
Install the sender gauge with the 5 screws.
- Torque:
- 1.5 N*m{15 kgf*cm, 13 in.*lbf}
- NOTICE:
- Be careful not to bend the arm of the fuel sender gauge assembly.
Connect the fuel sender gauge connector.
| 2. INSTALL REAR FLOOR SERVICE HOLE COVER |
Install the rear floor service hole cover with new butyl tape.
 |
| 3. INSTALL REAR NO. 7 AIR DUCT (w/ Rear Air Conditioning System) |
Attach the 4 clips to install the rear No. 7 air duct.
- HINT:
- Attach the clips in the order shown in the illustration.
 |
| 4. INSTALL REAR FLOOR MAT ASSEMBLY |
Attach the 5 clips to install the rear floor mat assembly.
 |
| 5. INSTALL REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System) |
Attach the claw to install the guide.
 |
Install the screw.
- HINT:
- Use the same procedures for both sides.
| 6. INSTALL AIR DUCT PLUG (w/ Rear Air Conditioning System) |
Attach the 2 claws to install the plug.
- HINT:
- Use the same procedures for both sides.
 |
| 7. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH |
- w/ Sliding Roof:
(Click here) - w/o Sliding Roof:
(Click here)
| 8. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH |
- w/ Sliding Roof:
(Click here) - w/o Sliding Roof:
(Click here)
| 9. INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
- HINT:
- Use the same procedure for rear seat cover caps.
Attach the 3 claws to install the rear seat cover cap.
 |
| 10. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE |
 |
Attach the 6 clips to install the rear floor mat support plate.
| 11. INSTALL REAR DOOR SCUFF PLATE LH |
 |
Attach the 3 claws and 4 clips to install the rear door scuff plate LH.
Install the screw.
| 12. INSTALL REAR DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 13. INSTALL REAR STEP COVER |
- HINT:
- Use the same procedure for both rear step covers.
Attach the 2 claws to install the rear step cover.
 |
| 14. INSTALL REAR NO. 2 SEAT ASSEMBLY |
- for Face to Face Seat Type:
(Click here) - except Face to Face Seat Type:
(Click here)
| 15. INSTALL REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side) |
| 16. INSTALL REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side) |
| 17. INSTALL CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
Connect the cables to the negative (-) main battery and sub-battery terminals.
| 18. CHECK SRS WARNING LIGHT |